Charles Isotransformer 93-IXFMR3/6-A Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 15

Charles Isotransformer 93-IXFMR3/6-A Скачать руководство пользователя страница 5

LT–IXFMR36–1

5

Charles Industries, Ltd. All rights reserved. Printed in the United States of America.

INSTALLING THE ISOTRANSFORMER

Choosing an Electrical Wiring Method

There are two wiring methods that can be used to install the IsoTransformer as an isolation transformer in accor-
dance with ABYC E-8 Alternating Current (AC) Electrical Systems on Boats. A third method, also in accordance
with ABYC E-8, can be used to install the IsoTransformer as a polarization transformer if desired. The third meth-
od is not preferred, because wiring the unit in the manner described circumvents the AC grounding conductor
isolation between shore and boat power and may require the use of a galvanic isolator to reduce galvanic corro-
sion.

Note:

Figure 1, Figure 2 and Figure 3 are reprinted with permission from the American Boat and Yacht Council
(ABYC). To obtain the complete standard referenced or any other standards contact:

American Boat and Yacht Council:

3069 Solomon’s Island Road
Edgewater, MD 21037
Telephone: 410.956.1050
FAX:

410.456.2737

«
...
3
4
5
6
7
...
»

Содержание Isotransformer 93-IXFMR3/6-A
















Отзывы:

Нет отзывов