Charles Isotransformer 93-IXFMR3/6-A Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 15

Charles Isotransformer 93-IXFMR3/6-A Скачать руководство пользователя страница 14

LT–IXFMR36–1

14

Charles Industries, Ltd. All rights reserved. Printed in the United States of America.

Securing Covers

After all connections and terminations have been made, the access cover should be re-installed using all hard-
ware supplied.

Applying Power

Power should only be applied after all connections and terminations have been made and the access cover is
secure. Plug in the shore power and turn on the appropriate circuit breakers to apply power. Refer to the section
on Proper Operation.

OPERATING THE ISOTRANSFORMER

Safety First

Follow all precautions in the IMPORTANT SAFETY INSTRUCTIONS section in this manual. Pay close attention
to the DANGER, WARNING and CAUTION boxes both within this manual and labeled on the unit.

Proper Operation

When properly installed and connected, the IsoTransformer will provide isolation between shore and boat power
while maintaining a one to one turns ratio (shore voltage equals boat voltage).

MAINTAINING THE ISOTRANSFORMER

To avoid serious injury or death from high voltage electrical shock, disconnect the AC shore power
before attempting any maintenance or cleaning.

WARNING – HIGH VOLTAGE

No adjustment or maintenance is required for the IsoTransformer other than periodic cleaning of the outside cabi-
net with a dry cloth and inspecting all connections for tightness and corrosion by a qualified service person.

TROUBLESHOOTING

If there is a problem with the IsoTransformer, first check that all connections are accurate and secure, and retest.
If all connections are good, contact Charles Marine Products for technical assistance.

WARRANTY & CUSTOMER SERVICE

Warranty

CHARLES MARINE PRODUCTS warrants the IsoTransformer will be free from defects in materials and work-
manship which cause mechanical failure for one (1) year, as set forth in the Limited Warranty. Review this warran-
ty carefully for information on what is covered by its terms. Complete and return the warranty registration card
within ten (10) days of purchase to establish proof of ownership and validate the warranty coverage. You must
provide notice of any alleged defect in material or workmanship within thirty (30) days of discovering the problem,
and within the warranty period. Follow the procedure outlined below to obtain warranty service.

Warranty Service and Repair

If the unit fails to operate properly after following all the instructions in the manual, or if the C-Charger requires
service, take the following steps.

1.

Return the C-Charger to:

Charles Industries, Ltd.
400 S.E. 8th Street
Casey, IL 62420

ATTN: Service Center

Note:

Shipping costs to and from the service center are your responsibility.

«
...
12
13
14
15
»

Содержание Isotransformer 93-IXFMR3/6-A
















Отзывы:

Нет отзывов