Charles Isotransformer 93-IXFMR3/6-A Скачать руководство пользователя страница 15

Страница: 15 / 15

LT–IXFMR36–1

Include a letter with your company name (if applicable), contact, return address, daytime phone num-
ber and the nature of the failure.

When service is complete, Charles Industries, Ltd. will return the C-Charger to you. If there are any
repair charges, a representative from Charles Industries will contact you with that information prior to
having the unit repaired.

Customer Service

If technical assistance or customer service is needed, contact Charles Marine Products at:

847/806-6300 (Customer Service)
847/806-6231 (FAX)

For correspondence only, mail to:

Charles Marine Products
Charles Center
5600 Apollo Drive
Rolling Meadows, IL 60008-4049

SPECIFICATIONS

The specifications for the IsoTransformer are listed in Table 2.

Table 2. IsoTransformer Specifications

Feature

Specification

Input Voltage

120 VAC

Input Current

30 Amps

Output Voltage

120 VAC

Output Current

30 Amps

KVA Continuous

3.6 KVA

Operating Frequency

60 Hertz

C Rise Insulation System 220A

120

Insulation Class

% Impedance

3.4

Operating Temperature

to 50

Approximate Weight

60 pounds

Height

8 inches

Width

10.5 inches

Width (excluding the mounting flange)

8 inches

Depth

10.5 inches

Содержание Isotransformer 93-IXFMR3/6-A
















Результаты поиска

Содержание Isotransformer 93-IXFMR3/6-A

Отзывы:

Charles Isotransformer 93-IXFMR3/6-A, Инструкция по установке и руководство пользователя, Страница: 15 / 15

Результаты поиска

Содержание Isotransformer 93-IXFMR3/6-A

Отзывы: