background image

Hold coupling nut and regulator 
as shown for proper connection 
to LP cylinder valve.

C

Str

ght

ai

6.

Turn the coupling nut clockwise to tighten to a full 

solid stop. The regulator will seal on the back-check 
feature in LP cylinder valve, resulting in some 
resistance. 

An additional one-half to three 

quarters turn is required to complete connection. 

Tighten by hand only - do not use tools.

NOTE:

If you cannot complete connection, disconnect
regulator and repeat steps 5 and 6. If you are still
unable to complete the connection,

 do not use this

Regulator!

Leak Testing Valve, Hose and Regulator

1. Turn control knob to OFF.

2.

Be sure regulator is tightly connected to LP cylinder.

3.

Completely open LP cylinder valve by turning hand 
wheel counter clockwise. If you hear a 

rushing sound

turn gas off immediately. There is a major leak at the 
connection. 

Correct before proceeding

.

4.

Brush soapy solution on areas where bubbles are 
shown.

5. “If growing”

 bubbles appear, there is a leak. Close 

LP cylinder valve immediately and re-tighten 
connections.

 If leaks cannot be stopped “do not try 

to repair”.

 Call for replacement parts. Order new 

parts by giving the part number from the parts list to 
the Service Center at 1-800-241-7548.

6.

Always close LP cylinder valve after performing leak 
test by turning hand wheel clockwise.

Safety Tips

s

Before opening LP cylinder valve, check the coupling 
nut for tightness.

s

When appliance is not in use, turn off control knob 
and LP cylinder valve.

s

Never move appliance while in operation or still hot.

s

The regulator may make a humming or whistling 
noise during operation. This will not affect safety or 
use of fireplace.

s

Check appliance before each use for buildup of 

any leaves or other material that will burn or block 

the burner ports. Clean when needed before 

using. Have appliance inspected annually by a 

qualified service person.

6

WARNING

• Do not insert any foreign objects into the 

valve outlet. You may damage the valve and 
cause a leak. Leaking propane may result in 
explosion, fire, severe personal injury or 
death.

• Never attempt to attach this appliance to the 

self-contained LP gas system of a camper 
trailer or motor home.

WARNING

• Do not use appliance until leak checked.

• If leak is detected at any time, STOP and call 

your fire department.

• If you cannot stop a gas leak, 

immediately

 

close LP cylinder valve and call a LP gas 
supplier or your fire department!

Содержание 7101399





















Отзывы: