background image

9  

CAUTION

Storing Your Grill

•Clean cooking grates.
•Store in dry location.
•When LP cylinder is connected to grill, store outdoors in a well-

ventilated space and out of reach of children.

•Cover grill if stored outdoors. Choose from a variety of grill 

covers offered by manufacturer.

•Store grill indoors ONLY if LP cylinder is turned off and 

disconnected, removed from grill and stored outdoors.

•When removing grill from storage, follow “

Cleaning the Burner 

Assembly

” instructions before starting grill.

SPIDER ALERT!

VALVE

CONTROL PANEL

SPIDER WEBS

INSIDE VENTURI

If you notice that your grill is getting hard to light or that the 
flame isn’t as strong as it should be, take the time to check and 
clean the venturi’s.

In some areas of the country, spiders or small insects have been 
known to create “flashback” problems. The spiders spin webs, build 
nests and lay eggs in the grill’s venturi tube(s) obstructing the flow of 
gas to the burner. The backed-up gas can ignite in the venturi behind 
the control panel. This is known as a flashback and it can damage 
your grill and even cause injury.

To prevent flashbacks and ensure good performance the burner and 
venturi assembly should be removed from the grill and cleaned 
before use whenever the grill has been idle for an extended period.

BURNER

SPIDER AND WEBS

INSIDE BURNER TUBE

General Grill Cleaning 

•Do not mistake brown or black accumulation of grease and 

smoke for paint.  Interiors of gas grills are not painted at the 
factory 

(and should never be painted)

. Apply a strong solution 

of detergent and water or use a grill cleaner with scrub brush 
on insides of grill lid and bottom. Rinse and allow to completely 
air dry. 

Do not apply a caustic grill/oven cleaner to painted 

surfaces.

 

• 

Plastic parts: 

Wash with warm soapy water and wipe dry.

 

Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

•Porcelain surfaces: 

Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner.

 

Use nonabrasive scouring powder 

for stubborn stains.

•Painted surfaces: 

Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

•Stainless steel surfaces: 

To maintain your grill’s high quality 

appearance, wash with mild detergent and warm soapy water 
and wipe dry with a soft cloth after each use. Baked-on grease 
deposits may require the use of an abrasive plastic cleaning 
pad. Use only in direction of brushed finish to avoid damage. 
Do not use abrasive pad on areas with graphics.

• Cooking surfaces:

 If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.

Meijer.com

Содержание 463262812

































Отзывы: