background image

8

Burner Flame Check

•Remove cooking grates and flame tamers. Light burners, rotate 

knobs from 

HI

 to 

LOW

. You should see a smaller flame in

 

LOW

 position than seen on 

HI.

 Perform burner flame check 

on sideburner, also. Always check flame prior to each use. If 
only low flame is seen refer to "Sudden drop or low flame" in 
the 

Troubleshooting Section

.

HI

LOW

Turning the Grill OFF with AUTO-CLEAN™

With the Autoclean feature you have two choices for turning off your 
grill; 

Manual

 and 

AUTO-CLEAN™

Manual Method

Turn all knobs, including the AUTO-CLEAN™ valve, to the 

OFF

 

position.

Turn 

OFF

 the LP cylinder by turning the handwheel clockwise to a 

full stop.

AUTO-CLEAN™ Method

After cooking is complete, set all main burner grill knobs to the 

high setting and close the grill lid. (AUTO-CLEAN™ shutdown 
should not be used on the sideburner.)

Push in and turn the AUTO-CLEAN™ knob to the clean position. 
Once at the clean position, release the knob and the green light 

should begin blinking.

The valve will now stay on for 15 minutes before turning off the 

gas to the burners.

After the clean cycle is complete, turn all knobs including 

the AUTO-CLEAN™ valve to the 

OFF

 position. 

Turn

 OFF 

the LP cylinder by turning the handwheel clockwise to a 

full stop. 

For safety in storing a grill, the LP cylinder should always be turned 

OFF

If red light comes on while green light is flashing, the  batteries will 

need to be replaced very soon.

Ignitor Check

•Turn gas off at LP cylinder.

 Press and hold electronic ignitor 

button.  "Click" should be heard and spark seen each time 
between each collector box or burner and electrode. See 

"Troubleshooting"

 if no click or spark.

Valve Check

•Important: Make sure gas is off at LP cylinder before 

checking valves

.  Knobs lock in  

position. To check 

valves, first push in knobs and release, knobs should spring 
back. If knobs do not spring back, replace valve assembly 
before using grill. Turn knobs to

 LOW

 position then turn back to  

position. Valves should turn smoothly.  

Hose Check

Before each use, check to see if hoses are cut, worn or kinked. 

Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified by manufacturer.

OFF 

 

OFF 

 

Match-Lighting

CAUTION

If ignition does NOT occur in 5 seconds, turn the 
burner controls OFF, wait 5 minutes and repeat the 
lighting procedure. If the burner does not ignite with 
the valve open, gas will continue to flow out of the 
burner and could accidently ignite with risk of injury.

Turn controls and gas source or tank OFF when not 
in use.

WARNING

Sideburner Ignitor Lighting

 

 Do not lean over grill while lighting.

1.Open sideburner lid. 

Turn 

ON

 gas at LP cylinder.

3.

Turn sideburner knob to 

HI

, push and hold ELECTRONIC 

IGNITOR button.

4.

If sideburner does NOT light, turn knob to 

OFF

, wait 5 minutes, 

then repeat lighting procedure.

Sideburner Match Lighting

1.Open sideburner lid. 

Turn 

ON

 gas at LP cylinder.

3.

Place lit match near burner.

4.

Turn sideburner knob to 

HI

.

Be sure burner lights and
stays lit.

4. 

Push in and turn the AUTO-CLEAN™ valve to the 

GRILL

 position.

2.

Push in and turn the AUTO-CLEAN™ valve to the 

GRILL

 position.

2.

Push in and turn the AUTO-CLEAN™

valve to the 

GRILL

 position.

 Do not lean over grill while lighting.

3. 

Open lid during lighting

 

 Do not lean over grill while lighting.

1. 

Turn 

OFF

 all gas burner control valves.

2. 

Turn 

ON

 gas at LP cylinder.

6. 

Push in and turn far right or far left burner knob to the 

HI

burner lights and stays lit.

7. 

Light adjacent burners in sequence by pushing knobs in and 

turning to the 

HI

 position.

5.

 Place match into match holder (hanging from side panel of 

grill). Light match; then light burner by placing match through 
the match light hole on right or left side of grill.

position, depending on match light hole selected. Be sure

When changing the batteries, please replace both batteries at the 
same time. Always replace with new batteries of the same type.

NOTE:

 Always follow the lighting instructions found in the instruction 

manual and also located on the inside of the cabinet door prior to 
using the Auto-Clean feature. Grill must be ignited prior to using the 
Auto-Clean feature.

NOTE: Your grill may NOT be equipped with a Sideburner!

Meijer.com

Содержание 463262812

































Отзывы: