background image

17

  

REV 41532-20120918

ENGLISH

 

41532

MAINTENANCE ANd STORAGE

Storage

The generator should be started at least once every 14 
days and allowed to run for at least 20 minutes . For 
longer term storage, please follow these guidelines .

Generator Storage

1 .  Add a properly formulated fuel stabilizer to the tank .
2 .  Be sure all appliances are disconnected from the 

generator .

3 .  Run the generator for a few minutes so the treated 

fuel cycles through the fuel system and carburetor .

4 .  Turn the fuel valve to the “Off” position .
5 .  Let the generator run until fuel starvation has 

stopped the engine . This usually takes a few minutes .

6 .  The generator needs to cool acompletely before 

cleaning and storage .

7 .  Clean the generator according to the maintenance section .
8 .  Change the oil .
9 .  Remove the spark plug and pour about 1⁄2 ounce 

of oil into the cylinder . Crank the engine slowly to 
distribute the oil and lubricate the cylinder .

10 . Reattach the spark plug .
11 . Store the unit in a clean, dry place out of direct 

sunlight .

disconnect the Battery

1 .  Remove the protective cover from the black/negative 

battery lead .

2 .  Disconnect the black/negative lead from the black/

negative terminal on the battery and store the cap 
screw (M5x10) and lock washer (M5) .

3 .  Repeat steps 1-2 for the red/positive battery lead .
4 .  Store the battery in a cool, dry place .

Charge the Battery

For generators equipped with batteries for electric 
starting, proper battery maintenance and storage 
should be followed . An automatic battery charger with 

Generator exhaust contains odorless and colorless 
carbon monoxide gas .

To avoid accidental or unintended ignition of your 
remote start generator during periods of storage, 
the following precautions should be followed:

 

– When 

storing the generator for short periods of 

time make sure that the Ignition Switch, the Fuel 
Valve and the Battery Switch are set in the 

OFF 

position . 

 

– When 

storing the generator for extended periods 

of time make sure that the Ignition Switch, the 
Fuel Valve and the Battery Switch are set in the 
the the 

OFF position and the battery leads have 

been 

disconnected from the battery . 

dANGER

A Float Charger will maintain the battery condition 
over long storage periods .

NOTE

Our engines work well with 10% or less ethanol 
blend fuels . When using blended fuels there are 
some issues worth noting: 

 

– Ethanol-gasoline blends can absorb more water 

than gasoline alone . 

 

– These blends can eventually separate, leaving 

water or a watery goo in the tank, fuel valve and 
carburetor . 

 

– With gravity-fed fuel supplies, this compromised 

fuel can be drawn into the carburetor and cause 
damage to the engine and/or potential hazards . 

 

– There are only a few suppliers of fuel stabilizer 

that are formulated to work with ethanol blend 
fuels .

 

– Any damages or hazards caused by using 

improper fuel, improperly stored fuel, and/
or improperly formulated stabilizers, are not 
covered by manufacture’s warranty . 

It is advisable to always shut off the fuel supply, 
run the engine to fuel starvation and drain the tank 
when the equipment is not in use for more than 30 
days .

NOTE

Generator Maintenance

Make certain that the generator is kept clean and stored 
properly . Only operate the unit on a flat, level surface in 
a clean, dry operating environment . DO NOT expose the 
unit to extreme conditions, excessive dust, dirt, moisture 
or corrosive vapors .

Use a damp cloth to clean exterior surfaces of the generator .
Use a soft bristle brush to remove dirt and oil .
Use an air compressor (25 PSI) to clear dirt and debris 
from the generator . 
Inspect all air vents and cooling slots to ensure that they 
are clean and unobstructed .

DO NOT use a garden hose to clean the generator .

Water can enter the generator through the cooling 
slots and damage the generator windings .

CAUTION

automatic trickle charging capability should be used to 
charge the battery . Maximum charging rate should not 
exceed 1 .5 amps . Follow the instructions included with 
the battery charger . The battery should be fully charged 
at least once per month .

Charge the Battery Cont’d.

Содержание 41532
































Отзывы: