background image

201033 - 6000W PORTAbLE GENERATOR

ASSEMbLY

16

ASSEMbLY

Your generator requires some assembly. This unit ships from our 
factory without oil. It must be properly serviced with fuel and oil 
before operation.

If you have any questions regarding the assembly of your 
generator, call our Technical Support Team at 1-877-338-0999. 
Please have your serial number and model number available.

Unpacking

1.  Set the shipping carton on a solid, flat surface.

2.  Remove everything from the carton except the generator.

3.  Carefully cut each corner of the box from top to bottom. Fold 

each side flat on the ground to provide a surface area to work 
with the generator.

Install the Wheel Kit

 

CAUTION

The wheel kit is not intended for over-the-road use. 

Install the Wheels

1.  Before adding fuel and oil, tip the generator onto it’s recoil 

end.

2.  Remove wheel hub cap (B) from wheel by inserting a small 

screwdriver into the slot provided and pry upward.

3.  Slide the roll pin (C) through the wheel (A) from the outside.

4.  Slide the roll pin through the mount point on the frame.

5.  Secure with the r-clip (D).

6.  Re-install hub cap on wheel.

7.  Repeat to attach the second wheel.

D

A

C

b

Install the Support Leg

1.  Attach the support leg (E) to the generator frame with flange 

bolts (F) and flange lock nuts (G).

2.  Slowly tip the generator back down so that it rests on the 

wheels and support Leg.

G

E

f

Add Engine Oil

 

WARNING

DO NOT attempt to crank or start the engine before it has been 
properly filled with the recommended type and amount of oil. 
Damage to the generator as a result of failing to follow these 
instructions will void your warranty.

 

NOTICE

The generator rotor has a sealed, pre-lubricated ball bearing 
that requires no additional lubrication for the life of the bearing.

 

NOTICE

The recommended oil type for typical use is 

10W-30 

automotive oil

. However, using the listed conventional oils 

shown in the “Recommended Engine Oil Type” chart may be 
used for typical use including the first 5 hours of the break-in 
run time period of the engine.

If running generator in extreme temperatures, refer to the 
“Recommended Engine Oil Type” chart.

-20

0

20

40

60

Ambient temperature

Recommended Engine Oil Type

80

100

120

-28.9

°F
°C

-17.8

-6.7

4.4

15.6

26.7

37.8

48.9

10W-30

5W-30 Full Synthetic

10W-40

5W-30

Содержание 201033



































Отзывы: