background image

  

16

100215

 

ENGLISH

MAINTENANCE AND STORAGE

Generator Maintenance

Make certain that the generator is kept clean and stored 
properly. Only operate the unit on a flat, level surface in 
a clean, dry operating environment. DO NOT expose the 
unit to extreme conditions, excessive dust, dirt, moisture 
or corrosive vapors.

Use a damp cloth to clean exterior surfaces of the generator.
Use a soft bristle brush to remove dirt and oil.
Use an air compressor (25 PSI) to clear dirt and debris 
from the generator. 
Inspect all air vents and cooling slots to ensure that they 
are clean and unobstructed.

DO NOT use a garden hose to clean the generator.

Water can enter the generator through the cooling 
slots and damage the generator windings.

CAUTION

Generator exhaust contains odorless and colorless 
carbon monoxide gas.

To avoid accidental or unintended ignition of your 
generator during periods of storage, the following 
precautions should be followed:

 

– When 

storing the generator for short or extended 

periods of time make sure that the LPG cylinder 
is disconnected from the generator and the Fuel 
Valve is set in the 

OFF position.

DANGER

Storage

Generator Storage

1.  Be sure all appliances are disconnected from the 

generator.

2.  Start up and run the generator for a short time.
3.  Turn the OPD valve on the cylinder to the “Closed” 

position.

4.  Let the generator run until fuel starvation has 

stopped the engine. This usually takes a few 
seconds.

5.  Turn the fuel valve on the generator to the “Off” 

position.

6.  The generator needs to cool completely before 

cleaning and storage.

7.  Disconnect the fuel hose from the LPG cylinder.
8.  Clean the generator according to the maintenance 

section.

9.  Change the oil.
10. Remove the spark plug and pour about 1⁄2 ounce 

(14.8 mL) of oil into the cylinder. Crank the engine 
slowly to distribute the oil and lubricate the cylinder.

11. Reattach the spark plug.
12. Store the unit in a clean, dry place out of direct 

sunlight.

 

– Store LPG tank disconnected from fuel hose and 

generator.

 

– Store LPG tank with the OPD valve in the 

“Closed” position.

 

– Do not store LPG tank in or around extreme 

heat. LPG gas is extremely flammable.

 

– Do not store LPG tank in or around extreme 

cold. LPG gas will freeze.

NOTE

Contact with LPG from either the cylinder, excess 
from the hose, or from any leaks may cause freeze 
burns on skin. Do not touch or spill LPG on bare skin.

WARNING

Generator Storage Cont’d.

After a period (short or extended) of non-use 
we recommend that you perform the following 
maintenance procedures for utmost user safety:

 

– Check all hoses and fuel lines before each use 

for any holes, cracking, abrasions, nicks, cuts, or 
any other form of damage. If any hose or fuel line 
is found to be damaged in any way, DO NOT use 
the unit until the damaged part has been properly 
replaced.

 

– DO NOT try and repair any worn or damaged hose 

or fuel line, replace it with a new part ONLY.

 

– Always check for gas leaks every time a hose 

or fuel line is replaced, or disconnected and 
reconnected to any fuel fitting. This will ensure 
that fuel is properly flowing to the unit and 
eliminate possible hazards.

WARNING

Содержание 100215































Отзывы: