Chamberlain Security+ 1245GMR-1/3HP Скачать руководство пользователя

Страница: 6 / 36

ASSEMBLY STEP 1

Attach the T-Rail to the Motor Unit

To avoid installation difficulties, do not run the
garage door opener until instructed to do so.

• Remove the two washered screws mounted in top

of motor unit.

• Position T-rail at a 45˚ angle to opener so one hole

in T-rail and motor unit line up.

• Thread one of the washered screws part way in.

Use only these screws! Use of any other screws
will cause serious damage to door opener.

• Align T-rail and styrofoam over sprocket. Cut tape

from T-rail, chain and styrofoam.

• REMOVE STYROFOAM.

USE ONLY THIS
TYPE AND SIZE
SCREW

Washered Screw
5/16"-18x1/2"

Styrofoam

T-rail
Hole

To avoid serious damage to opener, ONLY use screws
mounted in top of motor unit.

CAUTION

ASSEMBLY STEP 2

Attach the Chain to the Sprocket
and Install the Sprocket Cover

• Position chain over the sprocket. If necessary,

loosen the outer nut on the trolley to obtain more
chain slack.

• Insert the second washered screw. CAUTION: Use

only the screw previously removed from motor
unit!

• Tighten both screws securely through the T-rail into

the motor unit as shown.

• Install the sprocket cover: Insert the back tab in the

slot. Squeeze the cover slightly and insert the front
tab in the slot on the mounting plate.

Proceed to Assembly Step 3.

To avoid possible SERIOUS INJURY to fingers from
moving garage door opener:
• ALWAYS keep hand clear of sprocket while operating

opener.

• Securely attach sprocket cover before operating.

USE ONLY THIS
TYPE AND SIZE
SCREW

Washered Screw
5/16"-18x1/2"

Sprocket

Sprocket Cover

Mounting
Plate

Front Tab Slot

Back Tab Slot

WARNING

Содержание Security+ 1245GMR-1/3HP





































Результаты поиска

Содержание Security+ 1245GMR-1/3HP

Отзывы:

Похожие инструкции для Security+ 1245GMR-1/3HP

Бренды по названию

Популярные бренды

Chamberlain Security+ 1245GMR-1/3HP, Руководство пользователя

Результаты поиска

Содержание Security+ 1245GMR-1/3HP

Отзывы:

Похожие инструкции для Security+ 1245GMR-1/3HP

Бренды по названию

Популярные бренды