Chamberlain Security+ 1245GMR-1/3HP Скачать руководство пользователя страница 5

Страница: 5 / 36

SECURITY

✚

Single-Function Remote Control (1)

Straight Door
Arm Section

Curved Door
Arm Section

Safety Labels
and
Literature

Header Bracket

CEILING MOUNT ONLY

Sprocket Cover

2-Conductor Bell Wire
White & White/Red

Light Lens (1)

Remote Control
Visor Clip

Door Bracket

Door Control Button
with (2) 6ABx1-1/2" screws

(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with
2-Conductor White & White/Black Bell Wire
attached

Safety Sensor
Bracket (2)

One-Piece
T-rail

Styrofoam

Trolley

Chain
& Cable

Cable
Pulley Bracket

Your garage door opener is packaged in two cartons
which contain the motor unit and all parts illustrated
below. Accessories will depend on the model

purchased. If anything is missing, carefully check the
packing material. Parts may be stuck in the foam.
Hardware for installation is also listed below.

Carton Inventory

INSTALLATION HARDWARE

Hex Screw 5/16"-18x7/8" (4)

Lag Screw 5/16"-9x1-5/8" (2)

Lag Screw 5/16"-18x1-7/8" (2)

Clevis Pin 5/16"x2-3/4" (1)

Clevis Pin 5/16"x1-1/4" (1)

Clevis Pin 5/16"x1" (1)

Nut 5/16"-18 (4)

Lock Washer 5/16" (4)

Self-Threading Screw 1/4"-14x5/8" (2)

Insulated Staples (30)

Ring Fastener (3)

Dry Wall Anchors (2)

Rope

Handle

Rail Grease

Carriage Bolt 1/4"-20x1/2" (2)

Wing Nut 1/4"-20 (2)

Содержание Security+ 1245GMR-1/3HP





































Результаты поиска

Содержание Security+ 1245GMR-1/3HP

Отзывы:

Похожие инструкции для Security+ 1245GMR-1/3HP

Бренды по названию

Популярные бренды

Chamberlain Security+ 1245GMR-1/3HP, Руководство пользователя

Результаты поиска

Содержание Security+ 1245GMR-1/3HP

Отзывы:

Похожие инструкции для Security+ 1245GMR-1/3HP

Бренды по названию

Популярные бренды