Chamberlain Security+ 1245GMR-1/3HP Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

15

INSTALLATION STEP 7

Install the Light and Lens

INSTALL THE LIGHT

• Install a 75 watt maximum light bulb in the socket.

The light will turn ON and remain lit for
approximately 4-1/2 minutes when power is
connected. Then the light will turn OFF.

• If the bulbs burn out prematurely due to vibration,

replace with a Garage Door Opener bulb.

INSTALL THE LENS

• Locate and loosen (approximately 1/8") the two

screws near top of opener front panel. Position lens
against panel with slotted tabs directly below
screws. Slide lens up to seat tabs behind screws.
Snap bottom tabs of lens into panel slots. Retighten
top panel screws to secure lens.

INSTALLATION STEP 8

Attach the Emergency Release
Rope and Handle

• Thread one end of the rope through the hole in the

top of the red handle so "NOTICE" reads right side
up as shown. Secure with an overhand knot at
least 1" from the end of the rope to prevent
slipping.

• Thread the other end of the rope through the hole

in the release arm of the outer trolley.

• Adjust rope length so the handle is 6 feet above

the floor. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal
the cut end with a match or lighter to prevent
unraveling.

• To prevent possible SERIOUS INJURY or DEATH from

a falling garage door:

– If possible, use emergency release handle to

disengage trolley ONLY when garage door is
CLOSED. Weak or broken springs or unbalanced
door could result in an open door falling rapidly
and/or unexpectedly.

– NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

• NEVER use handle to pull door open or closed. If rope

knot becomes untied, you could fall.

Lens Slot

75 Watt Max.

Light Bulb

Lens Tab

Light
Lens

Panel Screw

Trolley

NOTICE

Overhand
Knot

Emergency
Release Handle

Rope

Trolley
Release Arm

WARNING

«
...
13
14
15
16
17
...
»

Содержание Security+ 1245GMR-1/3HP





































Отзывы:

Нет отзывов

Похожие инструкции для Security+ 1245GMR-1/3HP

Бренд: CAME Страницы: 24

Бренд: GATEXPERT Страницы: 31

Бренд: HySecurity Страницы: 69

SlideSmart CNX 15

Бренд: Nice Страницы: 48

Бренд: CAME Страницы: 128

CONDOR 500 / ONE

Бренд: Comunello Страницы: 34

X-pervisio 1000

Бренд: Visonic Страницы: 12

Бренд: Key Automation Страницы: 16

Бренд: V2 Страницы: 104

Бренд: Rival Страницы: 4

Бренд: Sectron Страницы: 39

Бренд: FAAC Страницы: 10

Бренд: Dea Страницы: 20

Бренд: Polaris Страницы: 135

Бренд: FAAC Страницы: 42

Бренд: CAME Страницы: 26

Бренд: Omker Страницы: 9

Бренд: Black & Decker Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды