Chamberlain Security+ 1245GMR-1/3HP Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

background image

To Open the Door Manually

DISCONNECT THE TROLLEY:

The door should be fully closed if
possible. Pull down on the
emergency release handle and lift
the door manually. To reconnect
the door to the opener, press the
door control push button.

TO RE-CONNECT THE TROLLEY:

The

lockout feature prevents the

trolley from reconnecting
automatically, Pull the emergency
release handle down and back
(toward the opener). The door can
then be raised and lowered
manually as often as necessary.
To disengage the lockout feature,
pull the handle straight down. The
trolley will reconnect on the next
UP or DOWN operation.

• To prevent possible SERIOUS INJURY or DEATH from

a falling garage door:

– If possible, use emergency release handle to

disengage trolley ONLY when garage door is
CLOSED. Weak or broken springs or unbalanced
door could result in an open door falling rapidly
and/or unexpectedly.

– NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

• NEVER use handle to pull door open or closed. If rope

knot becomes untied, you could fall.

28

Using the Wall-Mounted
Door Control

Press the button to open or close
the door. Press again to reverse the
door during the closing cycle or to
stop the door while it's opening.

PUSH
BUTTON

WARNING

LOCKOUT POSITION

MANUAL DISCONNECT

POSITION

Trolley
Release
Arm

NOTICE

Emergency
Release
Handle
(Pull Down)

Trolley
Release
Arm

NOTICE

Emergency
Release Handle
(Pull Down & Back
Towards Opener)

«
...
26
27
28
29
30
...
»

Содержание Security+ 1245GMR-1/3HP





































Отзывы:

Нет отзывов

Похожие инструкции для Security+ 1245GMR-1/3HP

Бренд: International Door Closers Страницы: 2

Бренд: DAAB Страницы: 8

Бренд: CAME Страницы: 20

Бренд: V2 Страницы: 22

Бренд: Key Automation Страницы: 60

Бренд: Tymetal Corp. Страницы: 38

Бренд: Protectrix Страницы: 2

Бренд: CAME Страницы: 12

Бренд: SOMFY Страницы: 12

Бренд: Chamberlain Страницы: 16

Бренд: Roger Technology Страницы: 16

AccessMaster Security+ M150

Бренд: Chamberlain Страницы: 36

Бренд: Roger Technology Страницы: 16

Бренд: quiko Страницы: 42

Бренд: CAME Страницы: 38

Бренд: GSM Activate Страницы: 6

Бренд: Beninca Страницы: 11

S450 UK KIT-CBAC

Бренд: FAAC Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды