1-en
Contents: General advice on installation and
use:
Contents list:
page 1
Content of the carton:
figure
Before you begin:
page 2
Checklist:
page 2
Gate types/installation height:
page 2, figure
A-F
Gate configuration:
page 2, figure
A-F
Gate stops:
page 2, figure
A-F
Assembly measurements and opening
angle:
pages 2-3, figures
A-B
Post bracket/Gate fixing bracket:
pages 2-3, figures
A-D
Release of drive arms:
page 3, figure
Installing the drive arms:
page 3, figure
A-B
Wiring:
page 3, figure
Maintenance work:
page 3
Initial Operation:
page 3
Technical Data:
page 3
Replacement Parts:
figure
CONTENT OF THE CARTON
(1)
Motor LYN & SCS (1/2)
(2)
Postbracket LYN & SCS
(3)
Keys per motor (2)
(4)
Gate fixing bracket LYN & SCS (1)
(5)
Capacitor 230V (1)
(6)
Manual (1)
(7)
LYN Clevis pin (2) and rings (4)
(8)
SCS Clevis pin (2) and rings (2)
(9)
SCS Nut (1) and Washer (1)
1
PLEASE START BY READING THESE IMPORTANT SAFETY RULES • SAVE THESE INSTRUCTIONS
This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal injury or
damage to property. Please read these warnings carefully.
This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and operated in
strict accordance with the following safety rules.
Incorrect installation and/or failure to comply with the following instructions may result in serious personal injury or proper
ty
damage.
1
2
3
3
5
6
7
8
Installation and wiring must be in compliance with
your local building and electrical installation codes.
Power cables must only be connected to a properly
earthed supply.
Any entrapment possibility by the moving wing between
wing & walls must be secured with safety edges or IR-
sensors.
Disconnect electric power to the system before making
repairs or removing covers.
A disconnecting device must be provided in the
permanently-wired installation to guarantee all-pole
disconnection by means of a switch (at least 3mm
contact gap) or by a separate fuse.
When using tools and small parts to install or carry
out repair work on a gate exercise caution and do not
wear rings, watches or loose clothing.
Make sure that people who install, maintain or operate
the gate drive follow these instructions.
Keep these
instructions in a safe place so that you can refer to them
quickly when you need to.
Please remove any locks fitted to the gate in order to
prevent damage to the gate.
It is important to make sure that the gate always runs
smoothly. Gates which stick or jam must be repaired
immediately.
Employ a qualified technician to repair
the gate, never attempt to repair it yourself.
Keep additional accessories away from children. Do not
allow children to play with pushbuttons or remote controls.
A gate can cause serious injuries as it closes.
After the installation a final test of the full function of
the system and the full function of the safety devices
must be done.
The full protection against potential squeeze or
entrappment must work direct when the drive arms are
installed.
This drive cannot be used with a gate incorporating a
wicket door unless the drive cannot be operated with
the wicket door open.
4
9
Содержание LiftMaster PROFESSIONAL LYN300 Series
