background image

20

INSTALLATION STEP 11

Fasten the Door Bracket 

Follow instructions which apply to your door type
as illustrated below or on the following page.

A horizontal reinforcement brace should be long
enough to be secured to two or three vertical
supports. A vertical reinforcement brace should
cover the height of the top panel. 

Figure 1 shows one piece of angle iron as the
horizontal brace. For the vertical brace, 2 pieces of
angle iron are used to create a U-shaped support.
The best solution is to check with your garage door
manufacturer for an opener installation door
reinforcement kit.

NOTE:

Many door reinforcement kits provide for

direct attachment of the clevis pin and door arm. In
this case you will not need the door bracket; proceed
to Step 12.

SECTIONAL DOORS

1. Center the door bracket on the previously marked

vertical centerline used for the header bracket
installation. Note correct UP placement, as
stamped inside the bracket.

2. Position the top edge of the bracket 2"-4" below

the top edge of the door, OR directly below any
structural support across the top of the door.

3. Mark, drill holes and install as follows, depending

on your door’s construction:

Metal or light weight doors using a vertical angle
iron brace between the door panel support and
the door bracket: 

• Drill 3/16" fastening holes. Secure the door bracket

using the two 1/4"-14x5/8" self-threading screws.
(Figure 2A)

• Alternately, use two 5/16" bolts, lock washers and

nuts (not provided). (Figure 2B)

Metal, insulated or light weight factory reinforced
doors: 

• Drill 3/16" fastening holes. Secure the door bracket

using the self-threading screws (Figure 3).

Wood Doors:

• Use top and bottom or side to side door bracket

holes. Drill 5/16" holes through the door and secure
bracket with 5/16"x2" carriage bolts, lock washers
and nuts (not provided). (Figure 4)

NOTE: 

The 1/4"-14x5/8"

self-threading screws are
not intended for use on
wood doors.

To prevent damage to garage door, reinforce inside of
door with angle iron both vertically and horizontally.

WARNING

CAUTION

WARNING

WARNING

Vertical
Centerline

Door
Bracket
Location

Header
Bracket

HORIZONTAL AND VERTICAL    
REINFORCEMENT IS NEEDED 

FOR LIGHTWEIGHT GARAGE 
DOORS (FIBERGLASS, 
ALUMINUM, STEEL, DOORS 
WITH GLASS PANEL, ETC). 
(NOT PROVIDED)

Door
Bracket

Vertical
Centerline

UP

Vertical
Reinforcement

Self-Threading
Screw
1/4"-14x5/8"

Door
Bracket

Nut
5/16"-18

Bolt
5/16"-18x2"

Lock  Washer
5/16"

Vertical
Centerline

UP

Vertical
Reinforcement

(Not Provided)

UP

Vertical
Centerline

Self-Threading
Screw
1/4"-14x5/8"

UP

Inside Edge
of Door or
Reinforcement Board

Bolt
5/16"x2"

Vertical
Centerline

(Not Provided)

Figure 1

Figure 2A

Figure 2B

Figure 3

Figure 4

Self-Threading
Screw
1/4"-14x5/8"

HARDWARE 
SHOWN 
ACTUAL SIZE

Содержание LiftMaster 2500





































Отзывы: