background image

© 2003, The Chamberlain Group, Inc.

114A2503G

All Rights Reserved

Printed in Mexico

LIFTMASTER SERVICE IS

ON CALL

OUR LARGE SERVICE ORGANIZATION

SPANS AMERICA

INSTALLATION AND SERVICE INFORMATION IS AS
NEAR AS YOUR TELEPHONE SEVEN DAYS A
WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER:

1-800-528-2817

HOURS: (Central Std. Time)

6:00 A.M. TO 7:00 P.M. Monday through Friday

8:00 A.M. TO 6:00 P.M. Saturday

8:00 A.M. TO 4:30 P.M. Sunday

www.liftmaster.com

For professional installation, parts and service,

contact your local LIFTMASTER/ CHAMBERLAIN
dealer. Look for him in the Yellow Pages, or call our
service number for a list of dealers in your area.

HOW TO ORDER

REPAIR PARTS

Selling prices will be furnished on request or parts will
be shipped at prevailing prices and you will be billed
accordingly.

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION:

• PART NUMBER

• PART NAME

• MODEL NUMBER

ADDRESS ORDERS TO:

THE CHAMBERLAIN GROUP, INC.
Technical Support Group
6020 S. Country Club Road
Tucson, Arizona 85706

SERVICE INFORMATION TOLL FREE NUMBER:

1-800-528-2817

LIFTMASTER GARAGE DOOR OPENER FIVE-YEAR LIMITED WARRANTY

The  Chamberlain  Group,  Inc.  (“Seller”)  warrants  to  the  first  retail  purchaser  of  this  product,  for  the  residence  in  which  this  product  is
originally  installed,  that  it  will  be  free  from  any  defect  in  materials  and/or  workmanship  for  a  period  of  60  full  months  from  the  date  of
purchase. Additionally,  the  motor  and  drive  belt  are  warranted  for  the  lifetime  of  the  product.  The  product  must  be  used  in  complete
accordance with Chamberlain’s instructions for installation, operation and care. 

The proper operation of this product is dependent on

your  compliance  with  the  Owner’s  Manual  instructions  regarding  installation,  operation,  maintenance  and  testing.  Failure  to
comply strictly with those instructions will void this warranty in its entirety. Please note that the safety reverse system, in order
to operate properly with your garage door, must be adjusted and periodically tested in accordance with the Owner’s Manual.

If, during the limited warranty period, it appears as though this product contains a defect which is covered by this limited warranty, 

CALL

OUR TOLL FREE SERVICE NUMBER, BEFORE DISMANTLING THIS PRODUCT, AT (1-800-528-2817).

Then send this product, pre-

paid and insured, to our service center for warranty repair. You will be advised of shipping instructions when you call the toll free service
number. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product that is returned for
warranty repair.
Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and covered by this limited
warranty, will be repaired or replaced (at Seller’s sole option) at no cost to you and returned pre-paid. Defective parts will be repaired
or replaced with new or factory-rebuilt parts at Seller’s sole option.

THIS  LIMITED  WARRANTY IS  IN  LIEU  OF  ANY OTHER  WARRANTIES,  EXPRESS  OR  IMPLIED,  INCLUDING  ANY IMPLIED
WARRANTY OF  MERCHANTABILITY OR  FITNESS  FOR A PARTICULAR  PURPOSE,  OR  OTHERWISE, AND  OF ANY OTHER
OBLIGATIONS  OR  LIABILITY ON  SELLER’S  PART.  THIS  LIMITED  WARRANTY DOES  NOT  COVER  NON-DEFECT  DAMAGE,
DAMAGE  CAUSED  BY IMPROPER  INSTALLATION,  OPERATION  OR  CARE  (INCLUDING,  BUT  NOT  LIMITED  TO  ABUSE,
MISUSE,  FAILURE  TO  PROVIDE  REASONABLE  AND  NECESSARY MAINTENANCE,  USE  OF  UNAUTHORIZED  PARTS  OR
ACCESSORIES,  UNAUTHORIZED  REPAIRS,  OR  ANY ALTERATIONS  TO  THIS  PRODUCT),  LABOR  CHARGES  FOR
DISMANTLING OR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF BATTERIES AND LIGHT BULBS,
OR  UNITS  INSTALLED  FOR  NON-RESIDENTIAL USE.THE  USE  OF  UNAUTHORIZED  PARTS  OR ACCESSORIES  WILL VOID
THIS LIMITED WARRANTY. If you have any questions as to whether accessories or replacement parts are authorized, please
contact Chamberlain.
THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE
DOOR  HARDWARE,  INCLUDING  BUT  NOT  LIMITED  TO  THE  DOOR  SPRINGS,  DOOR  ROLLERS,  DOOR  ALIGNMENT  AND
HINGES. ANY SERVICE  CALL THAT  DETERMINES  THE  PROBLEM  HAS  BEEN  CAUSED  BY ANY OF  THESE  ITEMS  COULD
RESULT IN A FEE TO YOU.
UNDER  NO  CIRCUMSTANCES  SHALL SELLER  BE  LIABLE  FOR  CONSEQUENTIAL,  INCIDENTAL OR  SPECIAL DAMAGES
ARISING  IN  CONNECTION  WITH  THE  USE  OF,  OR  INABILITY TO  USE,  THIS  PRODUCT.  IN  NO  EVENT  SHALL SELLER’S
LIABILITY FOR BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST
OF  THE  PRODUCT  COVERED  HEREBY.  NO  PERSON  IS  AUTHORIZED  TO  ASSUME  FOR  US  ANY OTHER  LIABILITY IN
CONNECTION WITH THE SALE OF THIS PRODUCT.

Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion
may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.

LIFETIME MOTOR & BELT WARRANTY

The motor and belt are fully warranted for the lifetime of the product to the first-time purchaser.

Содержание LiftMaster 2500





































Отзывы: