Chamberlain Elite RSL12V Скачать руководство пользователя страница 8

Страница: 8 / 32

To prevent SERIOUS INJURY or DEATH from a moving gate:
• Entrapment protection devices MUST be installed to protect anyone who may

come near a moving gate.

• Locate entrapment protection devices to protect in BOTH the open and close

gate cycles.

• Locate entrapment protection devices to protect between moving gate and

RIGID objects, such as posts or walls.

ADDITIONAL FEATURES

To reduce the risk of SEVERE INJURY or DEATH:
• READ AND FOLLOW ALL INSTRUCTIONS.
• ANY maintenance to the operator or in the area near the operator MUST NOT

be performed until disconnecting the electrical power and locking-out the power

via the operator power switch. Upon completion of maintenance the area MUST

be cleared and secured, at that time the unit may be returned to service.

• Disconnect power at the fuse box BEFORE proceeding. Operator MUST be

properly grounded and connected in accordance with national and local

electrical codes.

NOTE:

The operator should be on a separate fused line of

adequate capacity.

• NEVER let children operate or play with gate controls. Keep the remote control

away from children.

• ALWAYS keep people and objects away from the gate. NO ONE SHOULD CROSS

THE PATH OF THE MOVING GATE.

• Test the gate operator monthly. The gate MUST reverse on contact with a rigid

object or stop when an object activates the non-contact sensors. After adjusting

the force or the limit of travel, retest the gate operator. Failure to adjust and

retest the gate operator properly can increase the risk of INJURY or DEATH.

• Use the emergency release ONLY when the gate is not moving.
• KEEP GATES PROPERLY MAINTAINED. Read the owner’s manual. Have a

qualified service person make repairs to gate hardware.

• ALL maintenance MUST be performed by a LiftMaster professional.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted

and there are no obstructions to door travel.

• To reduce the risk of FIRE or INJURY to persons use ONLY LiftMaster part

29-NP712 for replacement batteries.

• SAVE THESE INSTRUCTIONS.

MAINTENANCE AND OPERATION

To protect against fire and electrocution:
• DISCONNECT power and battery BEFORE installing or servicing operator.

For continued protection against fire:
• Replace ONLY with fuse of same type and rating.

TROUBLESHOOTING

SAFETY

» IMPORTANT SAFETY INFORMATION

• ALWAYS wear protective gloves and eye protection when changing the battery

or working around the battery compartment.

Содержание Elite RSL12V

































Результаты поиска

Содержание Elite RSL12V

Отзывы:

Похожие инструкции для Elite RSL12V

Бренды по названию

Популярные бренды

Chamberlain Elite RSL12V, Руководство по установке

Результаты поиска

Содержание Elite RSL12V

Отзывы:

Похожие инструкции для Elite RSL12V

Бренды по названию

Популярные бренды