Chamberlain Elite RSL12V Скачать руководство пользователя страница 3

Страница: 3 / 32

CLASS I – RESIDENTIAL VEHICULAR GATE

OPERATOR

A vehicular gate operator (or system) intended for use in a home of one-to four

single family dwellings, or a garage or parking area associated therewith.

CLASS II – COMMERCIAL/GENERAL ACCESS

VEHICULAR GATE OPERATOR

A vehicular gate operator (or system) intended for use in a commercial location or

building such as a multi-family housing unit (five or more single family units) hotel,

garage, retail store or other building servicing the general public.

UL325 ENTRAPMENT PROTECTION REQUIREMENTS

This chart illustrates the entrapment protection requirements for the UL325 classes.

NOTE:

UL requires that all installations must have warning signs placed in plain

view on both sides of the gate to warn pedestrians of the dangers of motorized gate

systems.

GATE OPERATOR ENTRAPMENT PROTECTION

CLASS I CLASS II

B1 or B2

UL325

Classification

Primary Type

Secondary Type

Slide Gate Operator

SAFETY

» UL325 MODEL CLASSIFICATIONS

In order to complete a proper installation you must satisfy the entrapment

protection chart shown. That means that the installation must have one primary

means of entrapment protection and one independent secondary means of

entrapment protection. Both primary and secondary entrapment protection

methods must be designed, arranged or configured to protect against

entrapments in both the open and close directions of gate travel.

• Type A - Inherent (built into the operator) entrapment sensing

and at least one of the following as your secondary

entrapment protection:

• Type B1 - Non-contact sensors such as photoelectric sensors,

• Type B2 - Contact sensors such as gate edges

Содержание Elite RSL12V

































Результаты поиска

Содержание Elite RSL12V

Отзывы:

Похожие инструкции для Elite RSL12V

Бренды по названию

Популярные бренды

Chamberlain Elite RSL12V, Руководство по установке

Результаты поиска

Содержание Elite RSL12V

Отзывы:

Похожие инструкции для Elite RSL12V

Бренды по названию

Популярные бренды