12
INSTALLATION STEP 6
Install the Door Control
Locate door control within sight of the door at a
minimum height of 5 feet where small children cannot
reach, and away from moving parts of the door and door
hardware. The installation surface must be smooth and
fl at. If installing into drywall (Figure 1), drill 5/32" holes
and use anchors provided. For pre-wired installations
(as in new home construction), it may be mounted to
a single gang box (Figure 2).
NOTE:
After installation, a
green indicator light behind the cover will indicate proper
connection. If not lit, the Lock and Light features will not
function (reverse wires to correct).
1. Strip 1/4" of insulation from one end of bell wire
and connect to the two screw terminals on back of
door control by color: white wire to 2 and white/red
wire to 1. (Figure 3)
2.
Lighted door control:
Fasten to wall with 6ABx1-1/2"
self-tapping screws.
Multi-function door control:
Remove cover by gently
prying on a side corner near the top of the cover with
a small fl at head screwdriver (Figure 4). Fasten with
6ABx1-1/4" self-tapping screws (drywall installation) or
6-32x1" machine screws (into gang box) as follows:
• Drill and install bottom screw, allowing 1/8" to
protrude above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fi t.
• Install top screw with care to avoid cracking plastic
housing.
Do not overtighten.
• Insert bottom tabs and snap on cover. (To remove
cover after mounting, gently pry at top with paper
clip or small fl at head screwdriver.)
NOTE:
The push bar may stick if the door control is not
mounted on a smooth surface. If a click is not heard when
pressing the push bar, loosen the two mounting screws or
relocate the door control to a smoother surface.
3.
(Standard installation only)
Run bell wire up wall and
across ceiling to motor unit. Use insulated staples to
secure wire in several places. Do not pierce wire with a
staple, creating a short or open circuit.
4. Connect bell wire to the opener terminal screws as
follows: white to 2 and white/red to 1. (Figure 5)
5. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location
on inside of garage door.
NOTE:
DO NOT connect the power and operate the opener
at this time. The trolley will travel to the full open position
but will not return to the close position until the sensor
beam is connected and properly aligned. See Safety
Reversing Sensor Instructions beginning on page 15.
HARDWARE SHOWN ACTUAL SIZE
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing
door control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a
closing garage door:
• Install door control within sight of garage door,
out of reach of children at a minimum height of 5 feet
(1.5 m), and away from ALL moving parts of door.
• NEVER permit children to operate or play with door
control push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to
door travel.
• ALWAYS keep garage door in sight until completely
closed. NEVER permit anyone to cross path of closing
garage door.
2
1
RED WHT
WHT
-2
RED
-1
6ABx1-1/2" Screw
Lighted Door Control Button
6ABx1-1/4" Screw
(standard installation)
6-32x1" Screw
(pre-wired installation)
Insulated Staples
Drywall Anchors
Single Gang Box
To Replace Insert
Bottom Tabs First
To Replace Insert
Bottom Tabs First
24 Volt
Bell Wire
Bell Wire
Terminal
Screws
Top Mounting
Hole
PRE-WIRED
INSTALLATION
REMOVE COVER
MULTI-FUNCTION
DOOR CONTROL (BACK)
DOOR CONTROL
BUTTON (BACK)
STANDARD
INSTALLATION
Figure 3
Figure 1
Figure 2
Figure 4
KG
KG
1
3
9
7
5
1
3
9
7
5
2
3
1
Bell Wire
Light Button
Lock Button
Push
Button
Opener Terminal
Screws
Bottom
Mounting Hole
BACK PANEL
Figure 5
Push
Bar
