Challenger Lifts Magnum Versymmetric OE-9 Скачать руководство пользователя

Страница: 16 / 20

Model OE-9

Installation, Operation and Maintenance

Page 16

Rev. 02/1208

A1151_MAGNUM.doc

PARTS BREAKDOWN

(continued)

Fig C. Hydraulics

ITEM #

PART #

QTY/LIFT DESCRIPTION

A1201-15

POWER UNIT 1ph, 60 Hz, 208-230V

A1203-15

POWER UNIT 3ph, 60 Hz, 208-230/460V

16167

HYD ELBOW, 9/16 O-RING MALE TO #6 MALE FLARE

A1123-PU

HYD HOSE ASSEMBLY, POWER UNIT (22” LONG)

A1120

BULKHEAD TEE, #6 MALE 37 DEGREE FLARE

39101-024

COLUMN EXTENSION HOSE, OE-9-1 (24” LONG)

39101-048

COLUMN EXTENSION HOSE, OE-9-2 (48” LONG)

A1123-I

HYD HOSE ASSEMBLY, IDLER COLUMN (326” LONG)

A1122-12

HOSE CLAMP

16138

CYLINDER (68” STROKE X 2” BORE)

A1121

STRAIGHT ADAPTER, 9/16 MALE O-RING TO #6 MALE FLARE

A1123-P

HYD HOSE ASSEMBLY, POWER COLUMN (81” LONG)

Replace all worn or broken parts with genuine

Challenger Lifts Inc.

parts.

Contact your local Challenger Lifts Parts Distributor for pricing and availability.

(Call Challenger Lifts Inc. (502) 625-0700 for the Parts Distributor in your area)

Содержание Magnum Versymmetric OE-9





















Результаты поиска

Содержание Magnum Versymmetric OE-9

Отзывы:

Похожие инструкции для Magnum Versymmetric OE-9

Бренды по названию

Популярные бренды

Challenger Lifts Magnum Versymmetric OE-9, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum Versymmetric OE-9

Отзывы:

Похожие инструкции для Magnum Versymmetric OE-9

Бренды по названию

Популярные бренды