Challenger Lifts Magnum Versymmetric OE-9 Скачать руководство пользователя страница 6

Страница: 6 / 20

Model OE-9

Installation, Operation and Maintenance

Page 6

Rev. 02/1208

A1151_MAGNUM.doc

15) Assemble the sheaves, spacers and washers

onto the sheave pin as shown in

Fig 5

. Set in

cradle with all assembly parts between the
two plates.

Fig 5 –

Sheave Assembly

OCKING

AWL

16) Install Power Column locking pawl and lock

release clevis with 5/8” diameter x 1 1/2” lg
shoulder bolt and 1/2”-13 nylon lock nut,

Fig. 6.

Attach 3/8” O.D. extension spring to

upper hole in locking pawl and other end to
hole in bracket welded to column.

Fig 6 –

Locking Pawl Assembly

17) Attach ½” O.D. extension spring to hole

located on bottom side of Idler Column lock
pawl and install using 5/8” shoulder bolt and
lock nut,

Fig 6.

Attach 3/8” O.D. spring the

same as Power side.

YNCHRONIZER

ABLES

18) Manually raise the carriages approximately

32 inches to gain access to the cable-tie-off
tabs located on the carriage ladder. Insure
that the top of the hydraulic cylinder is out of
the way but still retained in the opening of the
top plate of the carriage as shown in

Fig 7a

19)

Note the cable trap device on the top
sheaves, remove the 3/8 bolt and
reassembly at each location after routing the

cable.

Fig 8

. Route synchronizing cables

using

Fig 7a

and attach ends to cable-tie-off

tabs using

Fig’s 7b & 7c

Fig 7a –

Cable Routing

Fig 7b –

Attaching Cable from Below

Fig 7c –

Attaching Cable from Above

Содержание Magnum Versymmetric OE-9





















Результаты поиска

Содержание Magnum Versymmetric OE-9

Отзывы:

Похожие инструкции для Magnum Versymmetric OE-9

Бренды по названию

Популярные бренды

Challenger Lifts Magnum Versymmetric OE-9, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum Versymmetric OE-9

Отзывы:

Похожие инструкции для Magnum Versymmetric OE-9

Бренды по названию

Популярные бренды