background image

1.0  Introduction 

 

 
2

 

1.0 Introduction 

THIS MANUAL is designed to help you get the most from your Challenge equipment.  Keep this 
manual in a safe, convenient place for quick reference by operators and service personnel. 
 

 SAFETY ALERT!  This symbol means CAUTION: Personal safety in-

structions!  Pay special attention to the instructions in bold type.  Personal injury may result if the 
precautions are not read and followed. 
 
 
READ THIS MANUAL BEFORE OPERATING!  Follow precautions and instructions given and you 
should have years of trouble-free operation.  If after reading the manual questions still remain, contact 
your Authorized Challenge Dealer. 
 
FOR PARTS AND SERVICE, contact the Authorized Challenge Dealer from whom you purchased 
your machine.  Use the illustrations and parts lists at the back of this manual to identify the correct 
parts needed.  Always give the SERIAL NUMBER and MODEL of your machine to insure the correct 
parts are sent as soon as possible. 
 
Take a few minutes right now to RECORD YOUR MACHINE SERIAL NUMBER in the space pro-
vided below.  Also be sure to fill out the warranty card accompanying your machine and return it 
DIRECTLY TO CHALLENGE. 
 
If you bought a used machine, it is important to have the following information on record at Challenge.  
Copy this page, fill in the information and send it care of The Challenge Service Department, 6125 
Norton Center Drive 

 Norton Shores 

 MI  49441-6081.  

 
 

CHALLENGE MODEL   

SERIAL NUMBER 

ATTN 

COMPANY 

 
ADDRESS 
CITY 

STATE/PROVINCE 

ZIP 

PHONE 

DATE INSTALLED 

DEALER NAME & CITY 

 

 
 

* WARRANTY INFORMATION * 

 

It is very important that you read and understand the conditions outlined in the Warranty Information 
Sheet 
attached to the outside of the shipping container of your machine. 
 
The Warranty Information Sheet must be filled out completely and returned to THE CHALLENGE 
MACHINERY COMPANY in order for the warranty to be issued for this machine. 

 

 
 
 

 

Challenge® is a registered trademark of 

The Challenge Machinery Company

 6125 Norton Center Drive

 Norton Shores, MI  49441-6081 

Copyright© 1999-2009 by The Challenge Machinery Company.  All rights reserved.  Printed in the U.S.A 

Содержание MS-10B






























Отзывы: