background image

HELPLINE NO 08454 505299

5

ORIGINAL INSTRUCTIONS

Safety warnings for lasers

SYMBOLS

To reduce the risk of injury, user

must read instruction manual

Warning

Wear eye protection

Wear ear protection

Wear dust mask

Double insulation

Waste electrical products should not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your Local Authority or

retailer for recycling advice.

This power tool produces class 2 
laser beams according to 
IEC EN 60825-1. 

Directly looking into the

laser beam – particularly with magnifying 
devices such as binoculars – can damage the 
eyes.

Protect yourself and your environment from 
accidents with suitable precautionary measures.

•  Do not look directly into the laser beam 

    without eye protection.

•  Never look directly in the beam path.
•  Never direct the laser towards reflective 

    surfaces, persons or animals. Even a 
    low-powered laser beam can cause 
    damage to the eyes.

•  Caution – following procedures that differ 

    from those stated here can lead to a 
    dangerous exposure to radiation.

•  Never open the laser line guide.

 

Wave length 650nm
Power max.<1mW

Содержание M1Q-DD4-80

















Отзывы: