background image

21

This appliance is suitable for  Natural gas or LPG. A gas conversion must be made by a competent  person.

17

18

If these solutions do not cure the fault, call a qualified professional

Fault

The boiler doesn’t start

Red indicator alight

Noises in CH system

Radiators rise in temperature During
summer season

Cause

No gas, no water or no electricity

Air in the gas pipe

Room thermostat switched off

Ignition lockout

Air presence in CH system or.
Insufficient pressure

Gravity effect in the CH system

Solution

Check the water pressure in the central
heating system and external electrical
supply, check that the gas supply is on,
should there still be a problem contact
your local service centre.

Contact your local service centre.

Turn up the room thermostat

Wait for a few minutes
Press the reset button 

36 (fig.21) the red

led will go out and the boiler attempts to
re-light.
If the red indicator lights too frequently,
please call your local service centre.

Purge of air the system and rise  up the
system pressure (chapter 8)

Close the heating flow isolating valve.
Don’t forget to open it again when you
will start heating.

Gas Conversion

Incorrect Operation

Helpful suggestions

-

Periodically check the system pressure using the pressure gauge and make sure that the pressure is between 1.0 and 1.5 
bar when the system is off and cool.  If the pressure is below the minimum recommended value, the pressure must be 
brought into the acceptable range.  Consult your installer for checking and refilling the system.
If the pressure level drops on a frequent basis, it is likely there is a water leak in the system. If this is the case, your 
installer must inspect the system.

-

The outer panel of the boiler’s case must only be cleaned with a damp cloth, do not use abrasive cleaners.  The control 
panel can be wiped with either a damp or dry cloth. Spray polishes must not be used on the control panel surface or 
knobs.  Care must be taken in preventing any liquid entering the appliance.

-

If the water is exceptionally hard, install a water softerner so that the efficiency of the boiler remains the same over time as 
this will consume less gas.

Содержание Centora green 24 Nat

























Отзывы: