Certikin MB055 Скачать руководство пользователя страница 28

Страница: 28 / 48

MB Pool & spa heater

3. To remove the manual reset high limit, follow the
procedure for the high limit thermostat but in
addition, disconnect the electrical connections
and release its mounting bracket from the side
panel by removing the M4 nut at the front of the
bracket. The thermostat can then be removed

from its bracket. Ensure thermostat phial is

correctly located in its pocket.

4. Reverse above procedure to reinstall.

185, 265 & 405 Models

MANUAL RESET HIGH LIMIT REMOVAL

1. Shut off main electrical power switch to

heater.

2. Remove inspection panels.

3. Disconnect electrical connections from

thermostat.

4. Remove defective high limit and replace

with a new high limit. Secure bulb in

pocket with chip provided.

5. Reverse above procedure to reinstall.

HIGH LIMIT REMOVAL (A.G.S.)

1. Shut off main electrical power

switch

heater.

2. Remove inspection panels.

3. Drain heater.

4. Remove defective high limit

and replace with a new high limit.

5. Reverse above procedure to reinstall.

All Models

PILOT SAFETY IGNITION

The heater employs a pilot safety which closes the
main gas valve within 8/10ths of a second whenever
the pilot fl ame is interrupted. Pilot fl ame is automati-
cally lit when the device is powered. Unit performs
its own safety check and opens the main valve only
after the pilot is proven to be lit.

BURNER DRAWER REMOVAL

1. Shut off main electrical power switch to

heater.

2. Shut off gas upstream of heater.

3. Remove front door.

4. Disconnect gas line from gas valve.

5. Remove (2) screws that mount burner tray

unit.

6. Disconnect wires that terminate at gas valve.

7. Slide out burner tray.

8. Reverse above procedure to re-install.

NOTE

IMPORTANT Reconnect Earth Connection

055, 105 & 155 Models

GAS VALVE REMOVAL

1. Remove burner tray. (See burner drawer

removal

procedure).

2. Disconnect pilot tubing from gas valve.

3. Remove gas valve with manifold from

burner

tray.

4. Remove manifold from gas valve.

5. Reverse above procedure to re-install.

185, 265 & 405 Models

GAS VALVE REMOVAL

1. Shut off gas supply to the heater. Remove

gas piping to gas valve inlet.

2. Disconnect wires, pilot tubing and bleed

line,

required.

3. Turn vertical gas pipe from manifold

slightly and unscrew gas valve.

4. Reverse above procedure to re-install.

All Models

MAIN BURNER AND INJECTOR REMOVAL

1. Remove burner drawer. See burner

drawer

removal

procedure.

2. Remove screws and burner hold down

bracket.

NOTE:

If the heat exchanger is sooted badly, the

burner hold down bracket and spacer can become
distorted from direct fl ame impingement and this
usually necessitates replacement of these parts.

3. Lift burners from slotted spacers and slide

from orifi ces. Clean with a wire brush.

4. Orifi ces usually do not need to be

replaced. To clean, run either copper wire

or a drill shank through orifi ce. Do not

enlarge hole. To remove orifi ce, use a

socket wrench and remove from manifold.

NOT

overtighten when reinstalling.

055, 105 & 155 Models

PILOT REMOVAL AND CLEANING

1. Remove burner drawer. (See burner

drawer

removal

procedure).

2. Disconnect pilot tubing, disconnect wires

from

gas

valve.

3. Disconnect pilot bracket from burner shield.

4. Remove pilot from bracket.

5. Remove pilot orifi ce, and clean with wire or

small

brush.

CAUTION! DO NOT

enlarge

hole in pilot orifi ce.

6. Reverse above procedure to re-install.

Содержание MB055

















































Результаты поиска

Содержание MB055

Отзывы:

Certikin MB055, Инструкция по эксплуатации, установке и обслуживанию, Страница: 28 / 48

Результаты поиска

Содержание MB055

Отзывы: