Certikin MB055 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 48

Certikin MB055 Скачать руководство пользователя страница 11

9

MB Pool & spa heater

CLEARANCES

ALL HEATERS
For clearances from combustible surfaces, see the
chart below.

CLEARANCE FROM COMBUSTIBLE

MATERIAL

(mm)

Plant Room Installation

Model

Top Back

Right

Left Front

055

900

50 150

150

Clear

105

900

50 150

150

Clear

155

1050 300

150 300 Clear

185-405

750

150

300

150 Clear

Outdoor

Installation

Model

Top Back

Right

Left Front

055

Clear 50 150

150

Clear

105

Clear 50 150

150

Clear

155

Clear 300

150

150

Clear

185-405

Clear 150

150

150 Clear

Forced Air
Inlet

For servicing, provide at least 600mm (24") in front
of the heater for burner tray removal, and at least
450mm (18") on water connection side of the heater
to inspect and delime the heat exchanger.

Heaters must not be installed under an overhang of
less than 1.0m (3 feet) from the top of the heater.
Three (3) sides must be open in the area under the
overhang. Roof water drainage must be diverted
away from the heaters installed under overhangs
with the use of gutters:
The point from where the fl ue products exit the heater
must be a minimum of 1.25m (4 feet ) below, four (4)
feet horizontally from or 0.3m (1 foot) above any
door, window or gravity inlet to a building. The top
surface of the heater shall be at least 1.0m (3 feet)
above any forced air inlet, or intake ducts located
within 3.0m (10 feet) horizontally.

HIGH WIND CONDITIONS
(OUTDOOR HEATERS ONLY)

In areas where high winds are frequent, it may be
necessary to locate the heater a minimum of 1.0 m
from high vertical walls, or install a wind break so the
heater is not in direct wind current.

«
...
9
10
11
12
13
...
»

Содержание MB055

















































Отзывы:

Нет отзывов