Ceragon FibeAir IP-10C Скачать руководство пользователя страница 53

Страница: 53 / 63

FibeAir® IP-10C

Installation Guide

Ceragon Proprietary and Confidential

Page 53 of 63

3.8

2+0 Dual Polarization (DP)

– Remote Installation

ACDP

When a remote configuration is required, the OMT is attached directly to the
antenna and the IP-10C units are installed remotely, using a flexible
waveguide. Before connecting WGs to the OMT, please connect mm to imperial
adaptor to the OMT



Frequencies 13-42 GHz do not require adaptors



Frequencies 6-11 GHz require adaptors, as described in the instructions
below.

Important!

Do not remove the transparent pressure window located on
the OMT ports!

The following components are necessary for a 2+0 DP remote installation:

Item

Description

Quantity Remarks

ANTENNA OMT ADAPTOR

RFU-C OMT

IP-10C

RFU-C OMT ADAPTOR KIT

Optional

RFU-C REMOTE MOUNT KIT 1

Freq. (WG standard)

6HGz (UDR70)

7-8GHz (UBR84)

10-11GHz (UBR100)

IPPON ADAPTORS OMT KIT RFU-C6-OMT-ADAPT RFU-C7_8-OMT-ADAPT RFU-C10_11-OMT-ADAPT

11 For 6Ghz (UDR70):

Mount the O-Ring supplied with the OMT kit.

ii Mount OMT Adaptor #1 on the OMT, and tighten using four M4 screws

and washers (supplied with the OMT adaptor kit).

iii Mount OMT Adaptor #2 on OMT Adaptor #1, and tighten using four M4

screws and washers (supplied with the OMT adaptor kit).

Содержание FibeAir IP-10C































































Результаты поиска

Содержание FibeAir IP-10C

Отзывы:

Похожие инструкции для FibeAir IP-10C

Бренды по названию

Популярные бренды

Ceragon FibeAir IP-10C, Руководство по установке

Результаты поиска

Содержание FibeAir IP-10C

Отзывы:

Похожие инструкции для FibeAir IP-10C

Бренды по названию

Популярные бренды