CENTURY PRODUCTS Ninja Pro Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

background image

Step 1 Lower side Frame Assembly
1. Attach the 90 degree aluminum angle support (2002-079 Bag #1) to the “inside” of the lower side frame. See
drawing below. Do this for the left and the right side. Each bracket is held on with three M3x8 cap head bolts and
Locknuts.
2. Attach two plastic battery tray mounts (2002-055 Bag #4) between the two lower side frames using four M3x8 self-
tapping screws. Install the battery tray plate (2002-113 Bag #1) using four M3x8 self-tapping screws. Please note that
there has been a change in the servo tray length. The mounts must be located at the very front and rear of the available
locations. Double check to make sure that the hole provided for the front cannot mount is on the proper side of the
battery tray.
3. Attach the two gyro plate cross members (2002-055) between the side frames using four M3x8 self-tapping screws.
Add gyro plate (2002-119 Bag #1) on top of the cross members with four M3x6 countersink screws. An optional gyro
location would be on the battery tray. This should only be considered if a center of gravity change is deemed necessary.

4

4

4

4

4

«
...
2
3
4
5
6
...
»

Содержание Ninja Pro





























Отзывы:

Нет отзывов

Похожие инструкции для Ninja Pro

Бренд: Laser Pegs Страницы: 2

Бренд: Makrlin Страницы: 8

Бренд: Old School Model Works Страницы: 20

Бренд: Walkera Страницы: 16

Бренд: L. G. B. Страницы: 37

Бренд: Amewi Страницы: 32

M-551 Sheridan Gulf War

Бренд: Eduard Страницы: 5

Бренд: Horizon Hobby Страницы: 19

Running worker with wheelbarrow

Бренд: Opitec Страницы: 5

Бренд: THINK GIZMOS Страницы: 25

Triple-the-Fun Art Studio

Бренд: Crayola Страницы: 3

Бренд: Ultrafly Страницы: 16

GLUE-N-GO F-4 PP KIT

Бренд: H-KING Страницы: 10

Sing & Discover Piano

Бренд: VTech Страницы: 10

FPV Kraftei 650 EPO

Бренд: TechOne Hobby Страницы: 5

SOPWITH CAMEL F.1

Бренд: Model Airways Страницы: 28

Бренд: Dromida Страницы: 4

Бренд: Power Wheels Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды