manualshive.com logo in svg

CENTURY PRODUCTS Ninja Pro, Инструкция по эксплуатации

Поделиться
Скачать
CENTURY PRODUCTS Ninja Pro Скачать руководство пользователя страница 16

Step 16 Main Rotor Blades
The rotor blades that are included in your Ninja Pro kit come
pre-finished and require no building. They however
should be checked for balance before use. If you have
a balancer follow the instructions that came with
the balancer. Next attach the blades to the rotor
head. Balance the Rotor head and blades on two
drinking glasses suspending the whole unit by the
flybar. The heavy side will hang lower than the light
side. Add self-adhesive tape on the light blade on a
location that will result in the proper CG shift. Add
the tape until the rotor head hangs horizontally.

Step 17 Radio Installation
All five servos are mounted with the screws that came with your radio system with the exception of the aft two
screws that hold the elevator servo. These two are replaced by two M3x8 self tapping screws. They are screwed
trough the cutouts in the frame and into the  plastic servo mounting plates (2002-169 BAG #3) located with the
plastic parts tree.  Mount the five servos as illustrated in the instructions.

Step 18 Making Up the Control Push rods
Make up all the control push rods according to the specified length shown in the drawing. Please note that these
dimensions are from end to end of the plastic rod-end and are only guidelines. You will have to fine adjust them
according to your particular servos.

#2002-213       ELEVATOR:              Total 91 mm for JR servos ( 2 )
(Use 68mm rod,see FIG #7  )              Total 92 mm for Futaba servos (2)

#2002-217       COLLECTIVE:         Total 117 mm for JR servos (2)
(Use 80mm rod,see FIG #2)              Total 118 mm for Futaba servos (2)

#2002-215       ROLL(AILERON):   Total131 mm for JR servos (2)
(Use 100mm rod,see FIG #1             Total 132 mm for Futaba servos (2)
 & FIG #3 Slightly bent 10 degree)

#2002-221       SWASHPLATE:        Total 69mm (4)
(Use 40mm rod, seeFIG #3A & FIG#3B)

#2002-221       PITCH ( long ):         Total 66mm ( 2 )
(Use 40 mm rod, see FIG #4 )

#2002-225       PITCH ( short ):        Total 36mm ( 2 )
(Use10mm rod, see FIG #4 )

#2002-219       FLYBAR:                  Total 47mm (2 )
(Use 25mm rod See FIG #5)

#2002-221       THROTTLE:             Total 80 mm (1 )
(Use 40 mm rod, see FIG #6)

# 2002-215 / 223 RUDDER:             Total 618mm (1 )
(Use 100 & 476 mm rod, see FIG #8)

EXSAMPLE:

2002-217

TOTAL 117mm(JR)

USE 80mm ROD

SEE FIG.# 2

117MM

80MM

CUT THIS
WHITE SHRINK
COVER OFF
THEN USE THIN
CA GLUE HERE

1 6

1 6

1 6

1 6

1 6

Содержание Ninja Pro





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды