Century Helicopter Products Swift Carbon 550 Скачать руководство пользователя страница 21

Страница: 21 / 30

(1) Dry fit the pinion gear to the main motor prior to mounting. Make

sure the main motor gear rides in line with the main gear on the Swift.

The key to installing the motor is the gear mesh. The elongated slots

for mounting the motor allow space to adjust the mesh between the

motor pinion gear and the main gear. Install the motor to the motor

mounting plate and secure with hardware provided by the manufac

turer of the motor.

(2) Install the batteries and control system neatly onto the electronics

tray. When installing electronics make sure that wires are not going to

come into contact with moving parts. Use foam rubber wrap to wrap

the receiver. ** The actual arranged components may be different

than the picture illustrates.

Motor

Mounting

Slots

Electric Motor

M3x16 Socket

head cap

screws (2)

1) When setting up the pitch of the tail blades, the tail pitch plate should be first set in the middle position of the tail rotor

shaft. The tail blades should have no pitch in that position. Tighten the tail rotor blades until the blade grips hold firm yet soft

enough so that the tail blades can still fold back in the event of a blade strike.

2) Adjust the position of the rudder servo bracket so that the tail pitch plate is centered on the tail rotor shaft while the servo

arm is at a 90 degree angle.

Tail rotor blades with zero pitch (blade

tips will be in-line)

Tail blades will line up in a flat straight line

Hint: Setting zero pitch for tail blades

Battery Pack

HINT:

Installing industrial strength velcro will

help secure the batteries during aerobatics.

NOTE:

The motor can be bolted

through the carbon battery tray

using the open spaces in the tray

and Main Gear

Mounting Motor and Electronics

Setting Tail Rudder Pushrod & Blades

8. Installing and Adjusting Control Components

As the rudder stick is moved

to the right, the rudder push

rod will move forward increas

ing the thrust in the tail blades

rotating the nose to the right.

MODE 1

MODE 2

(L) (R)

Deans Connectors

Regulator

Receiver

Switch mount

ESC

**You must install the correct

pinion to motor shaft before

installing the motor.**

For details on Motors and Pinions

See page 27.

Содержание Swift Carbon 550































Результаты поиска

Содержание Swift Carbon 550

Отзывы:

Похожие инструкции для Swift Carbon 550

Бренды по названию

Популярные бренды

Century Helicopter Products Swift Carbon 550, Инструкция по эксплуатации

Результаты поиска

Содержание Swift Carbon 550

Отзывы:

Похожие инструкции для Swift Carbon 550

Бренды по названию

Популярные бренды