Predator Gasser NX
Page 24
ONLY WITH SE/
CARBON KITS
Start by installing the
elevator bell crank as-
sembly, note that the
left side ball bearing is
flush with the pivot axle. On
the right side frame, the axle
extends outward from the frame
to attach the elevator arm. Install
four M3x8 socket cap screws into the
upper main shaft bearing block, front hex spac-
er and forewardmost lower bearing block. Install four
M3x8 socket cap screws into the clutchbell blocks
with M3 flat washers. Do not use any threadlock at
this time, these need to be loose until the main shaft
is installed and after the gear mesh has been set.
Align and press the rear ccpm arm onto the
exposed axle with the arm pointing to the
bottom of the upper side frames. This
is a tight fit, light tapping with a plas-
tic hammer will help here. Once
the arm is seated, install the
M3x10 button head screw to
secure it in place.
10
11
13 14
15
17
18
9
8
1
2
3
4
5
6
7
12
16
19
21
CNBB1280F
CNBB0730
CNLR1014
CNLR1020
CNM3X8FHCS
M3X8CS
HI6031
M3X10CS
M3X30CS
G10 Frames
20
编号
数量(PCS)
序号
1
2
3
4
5
6
2
1
1
2
1
1
7
9
1
1
2
8
10
(有头内六角螺丝)
1
14
13
15
(控制臂)
11
12
16
17
(轴承)
(M3球头螺丝)
(左摆臂)
(M3球头螺丝)
(固定块)
(斜头螺丝)
(侧板)
(间隔套)
(有头内六角螺丝)
(有头内六角螺丝)
(圆头螺丝)
(M3球头螺丝)
18
19
20
(有头内六角螺丝)
(插销)
(A型臂)
(A型臂固定座)
(轴承)
4
1
1
1
1
1
1
1
1
2
名称(ENGLISH-中文)
CNM3X8CS
CCPM ELEVETOR LEVER SET
CNBB0730
3x7x3 BALL BEARING
CNLR1014
CCPM CYCLIC BELL CRANKS
HI6031
CNLR1020
STAINLESS BALL, 3mm THREAD, MEDIUM
CNM3X8FHCS
HW6110
HI6031
CNM3X10CS
CNM3X30CS
CNLR1014
HI6032
CNM3X8CS
CNBB812F
HI6032
HI6032
HI6032
STAINLESS BALL, 3mm THREAD, SHORT
M3x8 FLUSH HEAD CAP SCREWS
M3x8 SOCKET HEAD CAP SCREWS
CCPM CYCLIC BELL CRANKS
M3x10 SOCKET HEAD CAP SCREWS
M3x10 SOCKET HEAD CAP SCREWS
M3x10 BUTTON HEAD CAP SCREWS
STAINLESS BALL, 3mm THREAD, SHORT
M3x8 SOCKET HEAD CAP SCREWS
CCPM ELEVETOR LEVER SET
CCPM ELEVETOR LEVER SET
CCPM ELEVETOR LEVER SET
8x12x3.5 ELEVATOR LEVER FLANGE BEARING
E.S.S.
CN2300
CN2300
(固定块)
E.S.S.
UPPER FRAME ASSEMBLY (G10)
AGL
UPPER SIDE FRAME G10 (LEFT)
CNM3X10BH
CNM3X10BH