Century Helicopter Products Predator Casser Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 59

background image

Predator Gasser NX

Page 54

In the closed position it will be difficult to reach the
set screw for the throttle arm. You should follow
these guidelines for optimal throttle performance
in the Predator Gasser.

The ball for the throttle lever must be placed in the
furthest hole from the center for best deflection.

Set the throttle to the full closed position.
The control ball on the throttle arm should be
aligned as pictured aligned with the brass ball
in the bulb plate.

This is the throttle control pointer plate. When
the set screw is tightned, the throttle arm moves
this plate.

Grab the throttle pointer and move it with your
thumb until exposing the set screw. Prepare
your index finger to hold the position of the
throttle arm.

After exposing the set screw carefully hold the
position of the throttle pointer and arm in order
to tighten the set screw.

Try testing the method of positioning the arm.
Tighten set screw with locktite only when position
is final.

The halfway point on the throttle is found by align-
ing the flat long end of the throttle pointer with
the bolt as shown.

Optimal Throttle Arm Positioning.

Following is a method of achieving maximum
deflection range in the throttle control. This
is the recommended setup to get top per-
formance out of your gas powered Predator.

THROTTLE ARM POSITION

«
...
52
53
54
55
56
...
»

Содержание Predator Casser




























































Отзывы:

Нет отзывов

Похожие инструкции для Predator Casser

Бренд: E-FLITE Страницы: 17

Habu 32 EDF ARF

Бренд: E-FLITE Страницы: 56

Бренд: Park Pilots Страницы: 12

Бренд: K'Nex Страницы: 28

Бренд: THUNDER TIGER Страницы: 28

Бренд: BlitzRCWorks Страницы: 12

Toot-Toot Drivers Press ‘n’ Go Vehicle

Бренд: VTech Страницы: 3

P-39 Q/N AIRACOBRA

Бренд: VQ Radio Control Model Страницы: 12

HISTORICAL TOWN GATE

Бренд: Faller Страницы: 8

P-51 MUSTANG EP RTF

Бренд: WattAge Страницы: 24

Antares C3M4 Combat Drone

Бренд: Warlord Games Страницы: 2

Бренд: marklin Страницы: 28

Eurofighter Typhoon V2

Бренд: Freewing Страницы: 17

Бренд: Badger Basket Страницы: 6

KROMLECH ORC BOOMKILLA DEFFSTOMPER BODY

Бренд: Tabletop Scenics Страницы: 21

Бренд: Little Tikes Страницы: 16

Бренд: marklin Страницы: 40

Бренд: KIDdesigns Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды