background image

 

 
 

 

Revision 1.4

   

January 2018  

© 2018 Centrica plc. Registered office: Millstream, Maidenhead Road, Windsor, Berkshire. SL4 5GD.  
Registered in England & Wales No 3033654  

PAN-10 and PAN-12 Sensor installation guide 

IC compliance statement  

This device complies with Innovation, Science and Economic Development 
Canada license-exempt RSS standard(s). Operation is subject to two conditions:  

1.  This device may not cause harmful interference, and  

2.   This device must accept any interference that may be received or that 

may cause undesired operation.  

A distance of at least 10 cm between the equipment and all persons should be 
maintained during the operation of the equipment.  

 
Le présent 

appareil est conforme aux CNR d’Industrie Canada applicables aux 

appareils radio exempts de licence. L’exploitation est autorisée aux deux 

conditions suivantes: 

 

1.  

l’appareil ne doit pas produire de brouillage, et

  

2.  

l’utilisateur de l'appareil doit a

ccepter tout brouillage radioélectrique 

subi, même si le brouillage est susceptible d'en compromettre le 
fonctionnement.  

Une distance d’au moins 10 cm entre l’équipement et toutes les personnes 
devraient être maintenues pendant le fonctionnement de l’équi

pement.  

Product end of use handling (WEEE) -  
Waste of Electrical and Electronic Equipment  

Panoramic Power is committed to protect the global environment and helping  
our customers with recycle responsibilities. Disposal of electrical and electronic 
products must be done according with the local and national regulations. You  
can return your product to a local collection point.  

For information about your disposal or collection points, call your distributer or 
vendor, or contact 

[email protected]

 

 

 

 

 

 

Содержание Panoramic Power PAN-10












Отзывы: