Central Pneumatic 33567 Assembly and Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 19

background image

SPECIFICATIONS

RATCHET WRENCH

—

Average Air Consumption

4 CFM

Recommended Air Pressure

90 PSI

Air Inlet

¼” NPT

Free Speed

150 RPM

Maximum Torque (ft. lbs.)

45

IMPACT WRENCH

—

Bolt Capacity

1/2"

Speed

7000 RPM

Air Inlet

¼” NPT

Sockets

7/16" – 1"

Maximum Torque (ft. lbs.)

230

SAVE THIS MANUAL

You will need the manual for the safety warnings and cautions, assembly instructions, operating
procedures, maintenance procedures, trouble shooting, parts list, and diagram

. Keep your

invoice with this manual. Write the invoice number on the inside of the front cover.

Keep

both this manual and your invoice in a safe, dry place for future reference.

SAFETY WARNING & CAUTIONS

WARNING: When using pneumatic equipment, basic safety precautions should always be
followed to reduce the risk of personal injury and hazards due to over pressurization.

READ ALL

INSTRUCTIONS BEFORE USING THIS TOOL!

1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.

2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit loca-

tions. Don’t expose to rain. Keep work area well lit. Do not use electrically powered air
compressors in the presence of flammable gases or liquids.

3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them

handle machines, tools, or hoses. Keep others a safe distance from tool while tool is in
operation as accidental actuation may occur, possibly causing injury.

4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to

inhibit rust. Always lock up tools and keep out of reach of children.

5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it

was intended. Do not use inappropriate attachments in an attempt to exceed the tool’s
capacities.

Page #2 -- SKU: 33567

REV 12/02

REV 05/04

For technical questions, please call 1-800-444-3353.

«
1
2
3
4
...
»

Содержание 33567 Assembly and




















Отзывы:

Нет отзывов

Похожие инструкции для 33567 Assembly and

Cordless Impact Wrench

Бренд: Milwaukee Страницы: 20

Бренд: Stanley Страницы: 7

Бренд: Kobalt Страницы: 45

Бренд: Kobalt Страницы: 132

Бренд: Sioux Tools Страницы: 35

Бренд: USAG Страницы: 56

Бренд: Racine Railroad Products Страницы: 18

Бренд: YATO Страницы: 132

Бренд: Raider Страницы: 104

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 20

Бренд: Fein Страницы: 3

Бренд: CLAS Страницы: 12

Бренд: Cornwell Tools Страницы: 4

bluePOWER CAT4280

Бренд: Cornwell Tools Страницы: 5

Бренд: DeWalt Страницы: 4

Бренд: DeWalt Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды