CELLmatic 1502 GSF Скачать руководство пользователя | Manualshive

Страница: 33 / 51

background image

CELLmatic 1502 – GSV/GSF

Issue: 2.1

User Manual

08.02.2004

Page 32 of 51

Thy

-

tronic

I/S – Bjørnevej 8c – DK 7700 Thisted – Tel.: +45 97982344 – Email.: [email protected]

DISPLAY PICTURES

Initial picture

01-01-94 17:25:35

F6 CLA :P-suct (C) 0.0 C
F5 SETUP 1 :Output (%) 0.0 %
F4 SETPOINT :Ampere (%) 0.0 %
F3 MANUAL :T-Oil (C) 0.0 C
F2 DISPLAY 2:P-discharge (B) 0.00 Bar
F1 STOP : STOP

P-SUCTION (C)

The suction pressure measured is shown here converted into degree Celsius.

OUTPUT (%)

The output is a calculated value indicating the output of the compressor in per cent.

AMPERE (%)

Showing the load of the compressor motor. Is indicated in per cent of the rated current of the motor.

T-OIL (C)

Indicating the oil temperature registered by the PT-100 sensor in the oil manifold.

P-DISCHARGE (C)

Indicating the discharge pressure in bar (normally measured in the oil separator).

All current values in this display picture are "frozen" in case of a cutout or a stop.

Display picture 2

01-01-94 17:25:35

F6 CLA :P-suct C 0.0 C
F5 SETUP 1 :P-suct setpt. C 0.0 C
F4 SETPOINT :P-discharge B 0.00 Bar
F3 MANUAL :P-oil B 0.00 Bar
F2 DISPLAY 3:C-abs % 0.0 %
F1 STOP : STOP

P-SUCTION C

The suction pressure measured is shown here converted into degree Celsius.

P-SUCTION SET POINT C

Here the set point for suction pressure is shown after which the compressor is adjusting provided it is
adjusting according to its own set point.

P-DISCHARGE B

Discharge pressure in bar measured with the pressure transmitter at the oil separator.

P-OIL PRESSURE B

Oil pressure in bar measured by the pressure transmitter in the oil manifold.

C-ABS %

If the slide stop is in minimum (Vi = 2.2) the slide valve has its longest possible travel. C-ABS is then a
linear output of this travel (0-100%). If the slide stop has been adjusted to a higher Vi the value of the
C-ABS will never reach 100%.

All values in display picture 2 are updated during standstill.

«
...
31
32
33
34
35
...
»

Содержание 1502 GSF




















































Отзывы:

Нет отзывов

Похожие инструкции для 1502 GSF

POWERMATE ES 5250 - S

Бренд: NEC Страницы: 18

POWERMATE VT 300 RELEASE NOTES

Бренд: NEC Страницы: 16

POWERMATE CT 815 - RELEASE NOTES

Бренд: NEC Страницы: 155

Бренд: NEC Страницы: 6

POWERMATE ES Series

Бренд: NEC Страницы: 132

POWERMATE ES Series

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 167

Бренд: NEC Страницы: 1

Color Computer 3 Basic

Бренд: Tandy Страницы: 17

TRS-80 Model II

Бренд: Tandy Страницы: 36

Бренд: Tandy Страницы: 337

Бренд: Tandy Страницы: 251

Бренд: Gateway Страницы: 72

Бренд: Rousseau Страницы: 7

Бренд: Avalue Technology Страницы: 15

UC-8100-ME-T Series

Бренд: Moxa Technologies Страницы: 22

Бренд: Risecom Corporation Страницы: 32

FlowControl FC-S01

Бренд: Go!Paint Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды