CELLmatic 1502 GSF Скачать руководство пользователя | Manualshive

Страница: 30 / 51

background image

CELLmatic 1502 – GSV/GSF

Issue: 2.1

User Manual

08.02.2004

Page 29 of 51

Thy

-

tronic

I/S – Bjørnevej 8c – DK 7700 Thisted – Tel.: +45 97982344 – Email.: [email protected]

01-01-93 17:25:35
SETPOINT/SETP R-U/SETP S/
F6 CLA :
F5 NEW (F5) :Vi compressor 2.6
F4 NEW (F4)
F3 NEW (F3) :Slide valve min 250 Ohm
F2 NEW (F2) :Slide valve max 2500 Ohm
F1 STOP :GSF Stop

F3:

Position for slide valve in minimum

F2:

Position for slide valve in maximum

SET POINTS

Set point T

03-06-96 13:48:15
SETPOINT/SETP R-U/SETP. T/
F6 STARTBOOS:AT Ready to run NO
F5 NEW (F5) :Cap. min.reg free 5.0 %
F4 NEW (F4) :P-suct setpt 2 -10.0 C
F3 NEW (F3) :Booster start 0.7 Bar
F2 NEW (F2) :Booster stop 4.5 Bar
F1 STOP :

F6: START

BOOSTER

Start the Booster compressor. When the compressor is in mode “Ready to Run”, Yes/No can be chosen.

F5:

CAP. MIN. REG.FREE

In case of master/slave operation this set point is important. When a slave is moving downward at a
time it will reach its minimum entered for capacity (entered under set point C/F5). When minimum has
been reached the master will receive a message and further downward adjusting is now taking place at
the master, see description of master/slave operation under types of duty. If the slave should go under its
minimum it will receive a capacity up signal. To avoid hunting at this set point "MIN REG.FREE" it is
possible to indicate by how many per cent over the minimum of the slave you will give a signal to the
master that the slave has reached its minimum.

F4:

P-SUCTION SETP 2

As mentioned under set point A it is possible to run according to an alternative set point for suction
pressure; "SUCTION PRESSURE 2" (in °C) which is entered here. It is adjusted according to set point
for suction pressure 2, when resistance input R IN 4 is ON.

F3: BOOSTER

START

When the suction pressure has reached this pressure signal is given for start of booster (= low-pressure
compressor). This signal is sent to digital output 18 (OUT18).

F2: BOOSTER

STOP

The booster compressor is stopped when the suction pressure of the high-pressure compressor reaches
this pressure that is OUT 18 goes "OFF". In case of stop of the high-pressure compressor the booster
compressor will be stopped too.

«
...
28
29
30
31
32
...
»

Содержание 1502 GSF




















































Отзывы:

Нет отзывов

Похожие инструкции для 1502 GSF

Бренд: Gateway Страницы: 278

Бренд: Neousys Technology Страницы: 73

Бренд: Moxa Technologies Страницы: 19

Бренд: Magic Страницы: 19

Hummingbird Lite

Бренд: Amico Страницы: 24

Бренд: Vivo Страницы: 8

Бренд: Acorn Страницы: 114

Бренд: Sony Страницы: 11

MSX2 HB-F9P Hit Bit

Бренд: Sony Страницы: 23

Бренд: Sony Страницы: 23

Бренд: Sony Страницы: 23

eVilla NTE-D101

Бренд: Sony Страницы: 41

Cyber-shot DSC-T50

Бренд: Sony Страницы: 43

Бренд: Sony Страницы: 72

Cyber-shot DSC-T50

Бренд: Sony Страницы: 120

Бренд: Sony Страницы: 194

Бренд: dynabook Страницы: 124

Бренд: BESTEK Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды