CELLmatic 1502 GSF Скачать руководство пользователя | Manualshive

Страница: 26 / 51

background image

CELLmatic 1502 – GSV/GSF

Issue: 2.1

User Manual

08.02.2004

Page 25 of 51

Thy

-

tronic

I/S – Bjørnevej 8c – DK 7700 Thisted – Tel.: +45 97982344 – Email.: [email protected]

SET POINTS

Set point J

01-01-94 17:25:35
SETPOINT/SETP I-L/SETP. J/
F6 CLA :
F5 NEW (F5) :Min T-oil alarm 10.0 C
F4 NEW (F4) :Min T-oil cut 5.0 C
F3 NEW (F3) :Max T-oil alarm 70.0 C
F2 NEW (F2) :Max T-oil cut 75.0 C
F1 STOP : STOP

F5:

MIN T-OIL ALARM

When the compressor is operating an alarm will be reported if the oil in the oil separator does not reach
this temperature. At the same time the message "ALARM LT-OIL" will appear at the top left-hand
corner of the display.

F4:

MIN T-OIL CUTOUT

The compressor will be stopped if the oil in the oil separator does not reach this temperature, and
"CUTOUT LT-OIL" will appear at the top left-hand corner of the display.

F3:

MAX T-OIL ALARM

If the oil temperature, measured in the oil manifold, is exceeding this temperature an alarm will be
reported, and "ALARM HT-OIL" will appear at the top left-hand corner of the display.

F2:

MAX T-OIL CUTOUT

If the oil in the manifold is exceeding this temperature the compressor will be stopped, and "CUTOUT
HT-OIL" will appear at the top left-hand corner of the display. Alarm and cutout of high oil temperature
has a delay of 3 minutes.

«
...
24
25
26
27
28
...
»

Содержание 1502 GSF




















































Отзывы:

Нет отзывов

Похожие инструкции для 1502 GSF

Бренд: Gateway Страницы: 126

Бренд: Panasonic Страницы: 15

st5548 - Thin Client

Бренд: Compaq Страницы: 39

Бренд: Gateway Страницы: 158

6275 - PC 300 GL

Бренд: IBM Страницы: 88

Бренд: IBM Страницы: 74

EPC-C301 Series

Бренд: Advantech Страницы: 80

Бренд: Matrox Страницы: 174

OFF65864 AIRLIFT 25

Бренд: Seville Classics Страницы: 4

Бренд: Acer Страницы: 88

Бренд: Acer Страницы: 90

Бренд: Clarke Страницы: 4

Height Adjustable Standing Desk 4-Leg

Бренд: Uplift Desk Страницы: 16

Бренд: Uplift Desk Страницы: 12

9120A4U - ThinkCentre A61 - 9120

Бренд: Lenovo Страницы: 66

Бренд: Lenovo Страницы: 76

Бренд: Lenovo Страницы: 64

Бренд: Lenovo Страницы: 98

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды