background image

 

 

14 

 

 

V9.14 

 

 

racks. If measuring liquid, the probe in a bottle with water and rubbing alcohol (10-
20%), use the rubber stopper to seal the bottle, and place the bottle in the racks. If 
the  bottle  probe  is  used  to  measure  air  temperatures,  the  differential  (HY)  on  the 
cooling  unit  should  be  set  to  “4”.  If  the  bottle  probe  is  used  to  measure  liquid 
temperature,  the  differential  should  be  set  to  “1”.  To  change  the  differential  on  the 
cooling unit, please refer to our “Advanced Operation” instructions in Section III.  

4.

 

The  unit  is  capable  of  operating  up  to  50  equivalent  feet  for  each  duct.  Elbows  or 
bends  will  reduce  this  length.  Use  a  duct  sizing  program  to  determine  the  total 
equivalent  feet  of  a  specific  duct  routing  design,  or  consult  the  manufacturer  for 
recommendations. 

5.

 

The  “High”  fan  speed  setting  is  required  for  long  duct  runs  and  as  ambient 
temperatures rise. The “Low” fan speed should never be used in a ducted application.  

6. Condensation on the hood can occur in warm and humid environments, even 
though the inside of the hood is insulated. If left unattended, this condensation 
may  cause damage to the  electrical  components  inside the  cooling unit. This 
damage is not covered by the cooling unit’s warranty. 

If condensation occurs on the front duct hood, you should do the following 
ASAP to mitigate the condensation: 

- Insulate the duct hood by adhering insulation to the outside of the hood. 
- Apply silicone caulking to the seam where the hood meets the cooling 
unit. 

Front Duct Kit - Cut Sheet

 

 

Содержание 6200VSi




























Отзывы: