CellarCool MAGNUM H.E. Скачать руководство пользователя страница 44

INSTALLING THE CONDENSING UNIT

Step 1: Select installation location

Before installing the outdoor unit, you must choose an appropriate 
location. The following are standards that will help you choose an 
appropriate location for the unit.

Proper installation locations meet the following standards:

Meets all suggested spatial requirements according to diagram

Good air circulation and ventilation

Firm and solid—the location can support the unit, is level, and will not vibrate

Protected from prolonged periods of direct sunlight or rain

Condensing unit is suggested to be mounted on concrete pad. Wall mounting is 

optional but will cause excess vibration.

DO NOT install unit in the following locations:

Near an obstacle that will block air inlets and outlets

Near a public street, crowded areas, or where noise from the unit will disturb others

Near animals or plants that will be harmed by hot air discharge

Near any source of combustible gas

In a location that is exposed to large amounts of dust

In a location exposed to a excessive amounts of salty air

In a closet or small room

Special Considerations For Cold Weather And Other Outdoor Conditions

If the unit is exposed to heavy wind:

 Install unit so that air outlet fan is at a 90° angle to the direction of the wind. If needed, build a barrier in front of the unit to protect it 
from extremely heavy winds.

If the unit is frequently exposed to heavy rain or snow:

Build a shelter above the unit to protect it from the rain or snow. Be careful not to obstruct air flow around the unit. Unit should be 

elevated to prevent build up of debris and snow in front of fan. 

Step 2: Anchor outdoor unit

The outdoor unit can be anchored to the ground or to a wall-mounted bracket.

 Unit Mounting Dimensions

The following is a list of different outdoor unit sizes and the distance between their mounting feet. Prepare the 

installation base of the unit according to the dimensions

Outdoor Unit Dimensions (in.)

 

Mounting Dimensions

Distance A (in.)

Distance B (in.)

31.18"L x 10.75”D x 21.18"H

19.72”

10.71”

Page 42 

08/09/21

Содержание MAGNUM H.E.




































































Отзывы: