Cedar Summit Paramount F25040 Скачать руководство пользователя страница 76

Страница: 76 / 144

[email protected]

REV.

DWG. NO.

SIZE

SCALE:1:50

WEIGHT:

Rock Wall Prep

SHEET 3 OF 3

See details for hardware

7-5/8

Wood Parts

Hardware

Other Parts

Step 22: Rock Wall Assembly

Complete Step 22, A-E twice to make 2 Rock Wall Assemblies.

Lay 2 (2776) Rock Rails down, side by side with angled edges

facing down. (fig. 22.1)

Place (2779) Access Board on the bottom of each (2776) Rock Rail

as shown in fig. 22.1. Make sure (2779) Access Board is flush to the

outside and bottom edges of each (2776). Attach using 4 (S20) #8 x

1-3/8” Wood Screws.

7-5/8” down from the top of both (2776) Rock Rails place 1 (2781)

Rk Board B, making sure the sides are flush to the outside edges of

each (2776) Rock Rail. Attach using 4 (S20) #8 x 1-3/8” Wood Screws.

(fig. 22.1)

In between the (2779) Access Board and (2781) Rk Board B stagger

2 (2781) Rk Board Bs and 2 (2780) Rk Board As using 4 (S20) #8 x

1-3/8” Wood Screws per board. Placing them as shown in fig. 22.1, this

will prevent rocks from forming a straight line. Make sure the boards

are evenly spaced and do not exceed 2-3/8” between boards.

Place 1 rock on each (2780) Rk Board A

and (2781) Rk Board B (fig. 19.2) and attach

using 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock

washer, flat washer and barrel nut) and 1

(S10) #8 x 1” Pan Screw per rock. The Screw

must be in the hole directly under the Pan

Bolt, it will stop the rock from spinning. (fig.

22.3)

Note: Gaps between boards

2-1/4”, not to exceed 2-3/8”

Note: The holes

in the rock boards

must orient to the

top of the boards.

7-5/8” Approx

Fig. 22.1

2779

2776

2780

2781

2780

Fig. 22.2

2 x

Access Board 1 x 6 x 19”

6 x

Rk Board B 1 x 6 x 19”

4 x

Rk Board A 1 x 6 x 19”

4 x

Rock Rail 1-1/4 x 2-1/2 x 51”

48 x #8 x 1-3/8” Wood Screw
10 x

#8 x 1” Pan Screw

10 x

1/4 x 1-1/4” Pan Bolt

(1/4” lock washer, 3/16” flat washer & 1/4” barrel nut)

2776

2780

2781

2779

Rock

10 x Rocks (6 green/4 yellow)

S10

PB2

Fig. 22.3

x 4 per

board

S20

FW0

LW1

BN1

S20

Содержание Paramount F25040

















































































































































Результаты поиска

Содержание Paramount F25040

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit Paramount F25040, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Paramount F25040

Отзывы:

Бренды по названию

Популярные бренды