Cedar Summit Paramount F25040 Скачать руководство пользователя страница 33

Страница: 33 / 144

[email protected]

Step 3: Swing Wall Prep

Part 4

It is important to assemble the frame on a flat, smooth surface.

On the remaining assembly attach (2630) SW Top to (2757) LT Post Assembly and (2758) RT Post Assembly

with 2 (WB1) 5/16 x 1” Wafer Bolts (with flat washer) connecting to previously installed t-nuts per assembly. (fig.

3.7 and 3.8)

Attach (2768) Panel Floor to (2757) LT Post Assembly and (2758) RT Post Assembly with 2 (H9) 1/4 x 1-1/4”

Hex Bolts (with lock washer and flat washer) connecting to previously installed t-nuts per assembly. (fig. 3.7)

Place 1 (2778) SW Ground MOD to each side of (2769) Panel BT Frame, notice the hole locations and attach

with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer and flat washer) per board connecting to previously installed

t-nuts. (fig. 3.7 and 3.9)

Place 1 (2607) Diagonal under (2778) SW Ground MOD on the right hand side so the top sits against (2758)

RT Post Assembly and loosely attach with 1 (H10) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut).

(fig. 3.7 and 3.9)

2 x

5/16 x 1” Wafer Bolt (5/16” flat washer)

2 x

1/4 x 1-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer)

3 x

1/4 x 2-1/4” Hex Bolt (1/4” lock washer, 1/4” flat washer and (1) 1/4” t-nut)

2 x

SW Ground MOD 5/4 x 4 x 14-1/4”

1 x

Diagonal 1-1/4 x 3 x 22”

Wood Parts

Hardware

2778

Fig. 3.8

Fig. 3.7

2758

2757

Note which bolt holes are used

x 2

2607

2630

2768

WB1

2607

x 3

WB1

2778

2769

2778

Fig. 3.9

x 2

FW1

LW1

FW2

TN1

H10

Содержание Paramount F25040

















































































































































Результаты поиска

Содержание Paramount F25040

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit Paramount F25040, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Paramount F25040

Отзывы:

Бренды по названию

Популярные бренды