manualshive.com logo in svg

Cedar Summit Paramount F25040, Инструкция по установке и эксплуатации

Поделиться
Скачать
Cedar Summit Paramount F25040 Скачать руководство пользователя страница 72

 

72 

[email protected]

Step 20:  Install Window and Wall Inserts 

Part 5 - Small Fort Front Wall

H:

  In the lower openings of the Small Fort Front Wall install 2 (2649) Lower Window Inserts and in the upper 

opening beside the Tunnel Side install 1 (2655) Upper Window Insert using 9 (S0) #8 x 7/8” Truss Screws per 

insert.  (fig. 20.18, 20.19 and 20.20)

I:

  In the right upper opening of the Small Fort Front Wall install 1 MOD 3-Pane Transom with 4 (S0) #8 x 7/8” Truss 

Screws.  (fig. 20.18, 20.19 and 20.21)

Fig. 20.18

Tunnel 

Side Wall

Tight

S0

S0

Fig. 20.20

Inside View

31 x 

#8 x 7/8” Truss Screw

1 x 

Upper Window Insert 1.27 x 18.8 x 35.86”

2 x  

Lower Window Insert 1.27 x 18.8 x 41.91”

2655

Wood Parts

Hardware

2649

S0

2649

2655

and

Fig. 20.19

Outside View

2655

2649

Small Fort

Inside View

MOD 3-Pane 

Transom

Tight

S0

Fig. 20.21

MOD 3-Pane 

Transom

2649

Front Wall

2601

1 x MOD 3-Pane Transom

Other Parts

Содержание Paramount F25040

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды