Cedar Summit Paramount F25040 Скачать руководство пользователя страница 38

Страница: 38 / 144

[email protected]

12 x

#8 x 2-1/2” Wood Screw

4 x

1/4 x 2-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 2-1/2” Lag Screw (1/4” flat washer)

Pre-drill all Lag Screws. On the Swing Wall side, from inside the assembly, tight to the End Wall, halfway up

the assembly,

5/8” down from the top of the panel board attach 1 (2777) Side Joist MOD to (2677) Narrow Panel

with 1 (H11) 1/4 x 2-3/4” Hex Bolt (with lock washer, flat washer and t-nut) and to (2768) Panel Floor with 1 (LS2)

1/4 x 2-1/2” Lag Screw (with flat washer). Bolt and Lag Screw are installed from inside the assembly. Make sure

(2777) Side Joist MOD is level then attach with 4 (S3) #8 x 2-1/2” Wood Screws. (fig. 4.5 and 4.6)

Tight to (2777) Side Joist MOD, 5/8” down from the top of (2768) Panel Floor attach (2682) Short Side Joist

with 1 (LS2) 1/4 x 2-1/2” Lag Screw (with flat washer). Lag Screw is installed from inside the assembly. Make

sure (2682) Short Side Joist is level and flush to the top of (2777) Side Joist MOD then attach with 2 (S3) #8 x

2-1/2” Wood Screws. (fig. 4.5 and 4.7)

Repeat E and F for the front Front/Back Wall side, except use 3 (H11) 1/4 x 2-3/4” Hex Bolts (with lock washer,

flat washer and t-nut) instead of the lag screws and (2777) Side Joist MOD is tight to the end Front/Back Wall and

is attached to (2772) Panel Floor Support. (2682) Short Side Joist is attached to (2677) Narrow Panel. (fig. 4.5

and 4.7)

Hardware

2 x

Side Joist MOD 2 x 2 x 40-1/4”

2 x

Short Side Joist 2 x 2 x 22-1/8”

Wood Parts

2777

2682

Tight

2777

H11

Fig. 4.6

Fig. 4.5

2677

2682

2772

2768

2777

End Wall

5/8”

Swing Wall

Front/Back

Wall (Front)

Step 4: Large Fort Frame Assembly

Part 4

2677

Front/Back

Wall (End)

Tight

2682

H11

LW1

FW1

TN1

H11

LS2

H11

LS2

Fig. 4.7

LS2

FW1

Содержание Paramount F25040

















































































































































Результаты поиска

Содержание Paramount F25040

Отзывы:

Бренды по названию

Популярные бренды

Cedar Summit Paramount F25040, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Paramount F25040

Отзывы:

Бренды по названию

Популярные бренды