35
34
Do not let water enter into the vacuum cleaner.
Keep the appliance in a cool, dry place and out of reach from children.
Do not immerse the device in water and do not clean any of its parts in the dishwasher.
Dust tank
To empty the dust tank, first disassemble the handheld vacuum cleaner from the rest of the
unit. Use the tab on the dust tank to open its cover and empty it. If necessary, shake it gently
to remove all the dust.
Fig. 11
(Рage 41)
To clean it, press the dust tank release button and turn the dust tank anticlockwise to the
unlock position. Remove it. Use water to rinse it. If necessary, clean it with soap to remove all
the dust.
Recommendation: It is suggested to clean the dust tank after each use.
Fig. 12
(Рage 41)
Filters
It is suggested to clean the filters regularly to ensure maximum efficiency. They can be
cleaned with warm water. Dry them thoroughly before installing them back in the device.
To take filters out:
Open the dust tank following the instructions on the before section.
Turn the metallic filter anticlockwise and remove it.
Fig. 13
(Рage 41)
Unscrew the plastic cyclone and remove it too.
Pull from the tab located on the top of the handheld vacuum cleaner and remove the high-
efficiency filter.
Wash all of them with warm water.
Allow them to dry completely before installing and using them again.
Fig. 14
(Рage 42)
Jalisco brush
Recommendation:
It is important to clean the brush regularly to avoid hair and other foreign objects from
tangling and to prevent blockages.
Press the brush release button on the bottom part of the suction base and remove the brush.
Wash it with warm water. Do not use detergents or soap.
Make sure it is completely dry before installing it back in the device.
Fig. 15
(Рage 42)
ENGLISH
7.
WET ACCESSORY
Before use
Take the product out of the box.
Remove all packaging materials. Keep the original box.
Make sure all the components are included and in good conditions, otherwise, contact
immediately the official Technical Support Service of Cecotec.
When you do not use the vacuum cleaner for a long
time, please remove the water tank and
empty the remaining water. Do not expose it to direct sunlight or to damp environments.
Mop installation/removal
Removing/installing the water tank
Fig. 16
(Рage 43)
In order to install/remove the cleaning cloth you must first disassemble the water tank from
the rest of the appliance.
In order to remove the water tank, use your foot to hold it against the ground and pull
upwards until it unclicks
from position.
Once the cloth has been installed and the water tank has been
filled, to reinstall the water
tank, simply push it back together until it clicks into position.
Note: Do not use cleaning agents. Use clean and room temperature water only. Do not use
the vacuum cleaner to vacuum water.
Installing the mop cloth
Place the mop cloth on the ground with the Velcro facing upwards.
Align the mop cloth with the Velcro strips on the water tank and attach it.
Fig. 17
(Рage 43)
Water emission
Fig. 18
(Рage 43)
When using this product for the first time, make sure the water tank lid is not fully open.
When not in use, pay attention to the water emission push button and
to the tank lid, as
water leak may occur when the water tank is full.
To activate water emission, the water emission push button must be pressed, and to stop
water emission, the push button must be released as shown on the following figure:
Note: If the vacuum cleaner is not going to be used for a long period of time, make sure to
remove the water tank and to empty the remaining water. Do not expose it to direct sunlight
or to damp environments.
Removing the mop cloth
To remove the mop cloth, just hold it with your hand and pull form it to detach it from the
water tank.
ENGLISH
CONGA ROCKSTAR 700 ULTIMATE ERGOWET
CONGA ROCKSTAR 700 ULTIMATE ERGOWET
