CDA WC140 Скачать руководство пользователя

Страница: 15 / 18

Installation

•

Do not install this appliance if it is damaged in any way. Installing a

damaged appliance may invalidate the warranty.

•

The water supply tap should be located in an adjacent cupboard so that it

can be accessed after installation.

•

Ensure the appliance is level by adjusting the feet as necessary.

•

Only use the water inlet supplied with the appliance.

•

If the water pressure is above 10 bar, a pressure relief valve should be used.

•

After connecting the water supply, check to ensure there are no leaks.

•

The water outlet can either be connected to a water drain or to a sink outlet

spigot. This connection should be at a minimum of 50 cm and a maximum

of 110 cm from the floor. The drain hose should be no longer than 4m in

length to ensure good performance from the dishwasher.

fig 14

fig 15

fig 16

Содержание WC140



















Результаты поиска

Содержание WC140

Отзывы:

Похожие инструкции для WC140

Бренды по названию

Популярные бренды

CDA WC140, Руководство по установке, использованию и обслуживанию

Результаты поиска

Содержание WC140

Отзывы:

Похожие инструкции для WC140

Бренды по названию

Популярные бренды