1. Incoming Junction Call on Ext to be transferred to another Tel Number/Cell number.
2. Making 2 Junction lines talk to each other while Ext remains out of the conversation.
Incoming Junction Call on Ext to be transferred to another Tel Number/Cell number
Any of the Extension can feed in a Telephone Number or Cell number on its extension whereby the incoming calls on its
extension would get diverted to those numbers.
While talking a tone will be heard after 2 minutes and if
is pressed then the call would get extended for another 2
minutes. Like this user can keep extending the talk time. If
is not pressed then the calls will disconnect. If user wishes to
disconnect in between then # need to be pressed.
Programming
:
Dial from your own Extension
#81
- Tel No (where calls are to be diverted to) - #
Increasing or decreasing the Talk time in such forwarded calls
:
#84TT
Where, TT= 01 to 99.
In default TT = 09 x 10 = 90 Secs (80 secs talk time and 10 secs Alert Time)
To cancel the feature, dial from your own Extension
#81#
Making 2 Junction lines talk to each other while Ext remains out of the conversation.
During conversation with a Junction line - Hook-Flash - # #
(To park the Call)
– 0 – Tel No (who is to be connected to the
previous Junction call)
– Hook Flash - # 6 - Now all 3 party can talk to each other but Ext can keep Handset down.
The 2 Junction lines will hear a tone after 80 seconds and if any of them presses * then they can talk for another 90
seconds. Like this they can keep extending the talk time. If * is not pressed then the calls will disconnect. If they wish to
disconnect in between then any of them need to dial #.
If the Ext wishes to rejoin the conference of two junction lines, the same can be done by dialing #9 from the Ext.
.
LCR (Least Call Routing)
– Manual
.
This feature allows the user to dial out telephone numbers through the cheapest Junction line.
In this mode, the user can pick particular Junction lines (called Special Junctions) to make Junction calls.
For Programming procedure
refer “Junction Grouping”
.
Memory Dialing
.
User can store up to 96 Telephone Numbers in the PBX. Those numbers can be dialed by any extension through a code
without the hassle of dialing the whole number.
However, if the extension is given only Local dialing facility, then it cannot dial STD numbers of the Memory.
Entering Telephone Numbers in the memory
Dial #
0000 + 46 CC NN….. #
Where, CC = Memory Code number from 01 to 96.
NN = Telephone Number of maximum 16 digits.
Deleting Memory Codes
Dial #
0000 + 46 CC # to delete a particular Memory Dialing Code.
Where, CC = Memory Code number from 01 to 96.
Dial #
0000 + 46 # to delete all Memory Dialing Codes.
Operation from Extension
Dial # 70 + CC = Memory Code number from 01 to 96
Allow / Disallow Memory Dialing to Selected Extensions
To allow memory dialing to an Extension, use
“Allowed Table” program as given below:
Dial #
0000 + 40 NN L # (L should be = 0 and NN= Last 2 Digits of the Original Extension Number)
Dial #
0000 + 43 01 1 # (With this program 1 digit is entered in location 01 of Allowed Table)
To disallow memory dialing to an Extension, use
“Junction Dialing Control” program as given below:
Dial #
0000 + 40 NN L # (L should be = 6 and NN= Last 2 Digits of the Original Extension Number)
.
Operator Extension Setting
.
In default Extension number 602 is defined as Operator and this extension can be changed if desired by the user.
When Operator extension is busy and another Junction call lands on it, a warning tone is heard by the Operator.
During this time dial FLASH #9.
The 2
nd
Call will get connected & the 1
st
Call will go on Hold.
Now, if required to talk to the first call then dial Flash + #9
To disconnect any of the 2 calls, keep handset down while talking to that Junction line.
Similarly 3
rd
Junction call can also be picked by the Operator by dialing Flash + #9. When 3 Calls are picked by Operator
and put on Hold, then on dialing Flash + #9 the first call on Hold will get retrieved first.
To change the Operator Extension, Dial #
0000 + 15NN#
Where, NN = Last 2 digits of Extension which is to be made the Operator.
Operator access code 0 cancellation
