CBL AirLaser IP100plus Скачать руководство пользователя страница 4

Страница: 4 / 50

Recommended safety precautions:



Do not look direct into the laser !



Do not look with any optical instruments into the laser !

Maximum transmitted power: 10 mW from each transmitter
Duration of pulses:

800 ps

Wavelength:

830 .. 870 nm

Beam divergence:

less than 2 mrad

Attention!

At fiber-port F1 on backplane, radiation class 1 will be emitted if open!

Safety precautions:
Do not look into the connector. When push or pull connectors, switch AirLaser off.

Infrared laser radiation – not visible!

Attention!

When cover open, laser radiation class 3B will be emitted!

AirLaser is waterproof sealed. Under the cover are no switches or indicators.

Warranty is void, if cover was open!

Flash protection:

CBL recommends to connect the installation-pole to protection ground.
AirLaser should be connected with the ground cable to the pole.
Certified flash protection together with the building protection is recommended.

Содержание AirLaser IP100plus



















































Результаты поиска

Содержание AirLaser IP100plus

Отзывы:

Похожие инструкции для AirLaser IP100plus

Бренды по названию

Популярные бренды

CBL AirLaser IP100plus, Руководство пользователя

Результаты поиска

Содержание AirLaser IP100plus

Отзывы:

Похожие инструкции для AirLaser IP100plus

Бренды по названию

Популярные бренды