CAVIDYNE Caviblaster 2570-D Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 35

background image

4.0 INSTALLATION

The CaviBlaster 2570-D must be installed in accordance with the requirements outlined
below. The unit can be installed in a vehicle to allow for maximum mobility and flexibility.

4.1 Uncrating and Lifting

Unpack the equipment and inspect for damage. If damage is

found, immediately

contact CaviDyne and the shipping company.

If the unit will not be installed

immediately, provide adequate indoor storage to protect against damage.

The CaviBlaster power unit should be lifted from underneath the frame using the
forklift channels or by using the lifting eyes provided on top of the frame. Verify
that lifting equipment is rated for the weight listed in Section 1.0

UNIT

SPECIFICATIONS

and that the unit is stable before lifting.

Figure 4.1 – Lifting Guidelines

Page - 13

CaviBlaster 2570-D Operations Manual

For more information please email [email protected] or call 1-(352)275-5319

«
...
11
12
13
14
15
...
»

Содержание Caviblaster 2570-D




































Отзывы:

Нет отзывов

Похожие инструкции для Caviblaster 2570-D

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: FENDT Страницы: 31

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: BARKO LOADERS Страницы: 85

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Magma Страницы: 16

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: ABB Страницы: 154

Бренд: popular Страницы: 27

Бренд: Milestone Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды