Cateye CC-TR200DW (V2c) Скачать руководство пользователя страница 4

Страница: 4 / 21

ENG

-7

ENG

-6

ENG

SPE

DEN

SPE

DEN

SPEED

2-2. Mount the magnet

1. Loosen the setscrews both on the SPEED side

and CADENCE side of the speed sensor, and turn
the sensor to the angle as shown on the right.

2. Temporarily secure the wheel magnet to the

spoke so that it faces the sensor zone on the
SPEED side.

3. Temporarily secure the cadence magnet inside

the crank with nylon ties, so that it faces the
sensor zone on the CADENCE side.

* When the speed sensor is not positioned ap-

propriately in respect to the two magnets (in both
Steps 2 and 3), move the speed sensor back
and forth so that it is positioned properly.
After you move the speed sensor, adjust the
position so that the two magnets face the rel-
evant sensor zone.

4. After adjustment, tighten the nylon ties firmly

to secure the speed sensor.

How to install the unit on your bicycle

When attaching the Flex Tight ™ bracket to the stem

* Attach the bracket with its open end facing to the right.

When attaching the Flex Tight ™ bracket to the handlebar

* Attach the bracket with its open end facing to the right.

Cut extra length of the band with scissors.

Caution:

Round off the cut edge of the bracket band to
prevent injury.

Bracket

Bracket band

Bracket rubber pad

Stem

Bracket

Bracket band

Bracket rubber pad

Handlebar

1. Attach the bracket to the stem or handlebar

The Flex Tight ™ bracket can be attached to either the stem or the handlebar depend-
ing on how the bracket and band are configured.

Caution:

Tighten the dial on the bracket band by hand only.
Over-tightening can damage the screw threads.

2. Mount the speed sensor and magnet

2-1. Temporarily secure the speed sensor

Locate the speed sensor on the left chain stay as shown
above, and loosely secure it with the nylon ties.

* Do not tighten the nylon ties completely at this stage.

Once a nylon tie is tightened, it cannot be pulled out.

Wheel magnet

Cadence magnet

Speed sensor

Nylon ties

Speed sensor

Wheel
magnet

Cadence
magnet

Nylon ties

Setscrew on the
CADENCE side

Sensor zone

Sensor
zone

Setscrew on the
SPEED side

Continue

Содержание CC-TR200DW (V2c)






















Результаты поиска

Содержание CC-TR200DW (V2c)

Отзывы:

Похожие инструкции для CC-TR200DW (V2c)

Бренды по названию

Популярные бренды

Cateye CC-TR200DW (V2c), Руководство по эксплуатации продукта

Результаты поиска

Содержание CC-TR200DW (V2c)

Отзывы:

Похожие инструкции для CC-TR200DW (V2c)

Бренды по названию

Популярные бренды