Adjusting Hand Alignment
If the hands are out of alignment even though
auto time adjustment is being performed, use
EDIFICE Connected to adjust them.
1.
Y
Tap the “EDIFICE Connected” icon.
2.
X
Hold down (C) for at least 1.5 seconds
until [CONNECT] starts to flash.
When a connection is established
between the watch and phone,
[CONNECT] will stop flashing and the
second hand will move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
3.
Y
Perform the operation shown on the
phone screen to correct hand alignment.
Phone Finder
You can use phone finder to trigger a tone on
the phone to make it easy to find. The tone is
forced to sound even if the phone is in vibrate
mode.
Important!
●
Do not use this function in areas where
phone call tones are restricted.
●
The tone sounds at a high volume. Do
not use this function when listening to
phone output over earphones.
1.
X
If the watch is connected with a phone,
press any button to terminate the
connection.
Connected
Disconnected
2.
X
If the watch is in any mode besides the
Timekeeping Mode, hold down (D) for at
least two seconds to enter the
Timekeeping Mode.
3.
X
Hold down (E) for at least 1.5 seconds
until the second hand moves to [R].
The phone will sound a tone when it
establishes a connection with the watch.
●
It will take a few seconds before the
phone tone sounds.
Connected
Searching for phone
4.
X
Press any button to stop the tone.
●
You can press any watch button to stop
the phone tone only during the first 30
seconds after it starts to sound.
Configuring Watch Settings
Timer start time and other settings can also be
configured using EDIFICE Connected.
1.
Y
Tap the “EDIFICE Connected” icon.
2.
X
Hold down (C) for at least 1.5 seconds
until [CONNECT] starts to flash.
When a connection is established
between the watch and phone,
[CONNECT] will stop flashing and the
second hand will move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
3.
Y
Select the setting you want to change
and then perform the operation shown on
the phone screen.
Changing the Home City
Summer Time Setting
1.
Y
Tap the “EDIFICE Connected” icon.
2.
X
Hold down (C) for at least 1.5 seconds
until [CONNECT] starts to flash.
When a connection is established
between the watch and phone,
[CONNECT] will stop flashing and the
second hand will move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
3.
Y
Perform the operation shown on the
phone screen to change your Home City
summer time setting.
Checking the Watch Charge
Level
Use the procedure below to check the current
charge level with EDIFICE Connected.
1.
Y
Tap the “EDIFICE Connected” icon.
2.
X
Hold down (C) for at least 1.5 seconds
until [CONNECT] starts to flash.
When a connection is established
between the watch and phone,
[CONNECT] will stop flashing and the
second hand will move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
3.
Y
Use EDIFICE Connected to check the
charge level.
Operation Guide 5537
8